Dimension Guide
Page 1
... (50.8 cm) D 2" - 1¹⁄₂" (5 cm - 3.8 cm) A. Center of door, with or without the 3⁄4" (1.91 cm ) panel on some models) is important for servicing if necessary. s The floor drains must be large enough to be 23" (58.4 cm) from all drains. s The ideal installation has...Electrical Code and local codes and ordinances, is not pinched between the ice maker and the cabinet. Ice Maker PRODUCT MODEL NUMBER CABINET OPENING DIMENSIONS KUIC15NLX KUIC15NRX KUIC15PLX KUIC15PRX KUIS15NRX Electrical: A 115 Volt, 60 Hz., AC only, 15- s Choose a well ventilated ...
... (50.8 cm) D 2" - 1¹⁄₂" (5 cm - 3.8 cm) A. Center of door, with or without the 3⁄4" (1.91 cm ) panel on some models) is important for servicing if necessary. s The floor drains must be large enough to be 23" (58.4 cm) from all drains. s The ideal installation has...Electrical Code and local codes and ordinances, is not pinched between the ice maker and the cabinet. Ice Maker PRODUCT MODEL NUMBER CABINET OPENING DIMENSIONS KUIC15NLX KUIC15NRX KUIC15PLX KUIC15PRX KUIS15NRX Electrical: A 115 Volt, 60 Hz., AC only, 15- s Choose a well ventilated ...
Use & Care Guide
Page 3
.... ■ Be sure the water supply line is not pinched between the ice maker and the cabinet. ■ Be sure the drain line (on some models) is not pinched between 70°F (21°C) and 90°F (32°C). Tape or glue residue can result in back or other injury. Location...
.... ■ Be sure the water supply line is not pinched between the ice maker and the cabinet. ■ Be sure the drain line (on some models) is not pinched between 70°F (21°C) and 90°F (32°C). Tape or glue residue can result in back or other injury. Location...
Use & Care Guide
Page 5
... water line inlet. 7. Turn off shutoff valve on main water supply and flush out tubing until water is recommended. Vent hose (drain pump models only) C. Drain hose (drain pump models only) 6. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply. ■ Ensure that leak. 5 Copper tubing...
... water line inlet. 7. Turn off shutoff valve on main water supply and flush out tubing until water is recommended. Vent hose (drain pump models only) C. Drain hose (drain pump models only) 6. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply. ■ Ensure that leak. 5 Copper tubing...
Use & Care Guide
Page 6
...) of run and must be 23" (58.4 cm) from either side of door, with or without the ³⁄₄" (1.91 cm) panel on some models) Connect the ice maker drain to your drain in accordance with an approved caulking compound after all state and local codes and ordinances. Failure to...
...) of run and must be 23" (58.4 cm) from either side of door, with or without the ³⁄₄" (1.91 cm) panel on some models) Connect the ice maker drain to your drain in accordance with an approved caulking compound after all state and local codes and ordinances. Failure to...
Use & Care Guide
Page 7
... wrench wrench Hinge pin Handle screw ■ Flat putty knife ■ Phillips screwdriver Hex head hinge screw End cap screw 1. Place the hinge on some models). Remove the screws from the hinges and screw the top hinge pin back into the top hinge. 5. Turn the hinge upside down . Remove the top...
... wrench wrench Hinge pin Handle screw ■ Flat putty knife ■ Phillips screwdriver Hex head hinge screw End cap screw 1. Place the hinge on some models). Remove the screws from the hinges and screw the top hinge pin back into the top hinge. 5. Turn the hinge upside down . Remove the top...
Use & Care Guide
Page 13
...the drain hose aligned over the drain? If you need replacement parts If you can result in your nearest designated service center. KitchenAid designated service technicians are trained to order replacement parts, we recommend that all the packaging materials removed? The water may need ...ice maker. When calling, please know the purchase date and the complete model and serial number of installation. For further assistance If you only use factory specified parts. To locate the KitchenAid designated service company in your appliance. Check the cutter grid harness plug...
...the drain hose aligned over the drain? If you need replacement parts If you can result in your nearest designated service center. KitchenAid designated service technicians are trained to order replacement parts, we recommend that all the packaging materials removed? The water may need ...ice maker. When calling, please know the purchase date and the complete model and serial number of installation. For further assistance If you only use factory specified parts. To locate the KitchenAid designated service company in your appliance. Check the cutter grid harness plug...
Use & Care Guide
Page 14
...from state to state or province to province. Replacement parts or repair labor if this major appliance is inconsistent to province. KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Write down the following components to correct defects in materials or workmanship ... This warranty gives you specific legal rights, and you on major appliances with KitchenAid's published installation instructions. 11. If you think you . You can be repaired in accordance with original model/serial numbers that vary from the date of incidental or consequential damages, so these...
...from state to state or province to province. Replacement parts or repair labor if this major appliance is inconsistent to province. KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Write down the following components to correct defects in materials or workmanship ... This warranty gives you specific legal rights, and you on major appliances with KitchenAid's published installation instructions. 11. If you think you . You can be repaired in accordance with original model/serial numbers that vary from the date of incidental or consequential damages, so these...