KitchenAid KUIP15PRXX Support and Manuals
Get Help and Manuals for this KitchenAid item
View All Support Options Below
Free KitchenAid KUIP15PRXX manuals!
Problems with KitchenAid KUIP15PRXX?
Ask a Question
Free KitchenAid KUIP15PRXX manuals!
Problems with KitchenAid KUIP15PRXX?
Ask a Question
Popular KitchenAid KUIP15PRXX Manual Pages
Use & Care Guide - Page 2
... Cleaning 11 Vacation and Moving Care 13
TROUBLESHOOTING 14 Ice Maker Operation 14 Ice Production 14 Ice Quality 15 Plumbing Problems 15
ASSISTANCE OR SERVICE 15 In the U.S.A 15 In Canada 15
WARRANTY 16
TABLE DES MATIÈRES
SÉCURITÉ DE LA MACHINE À GLAÇONS 17
INSTRUCTIONS D'INSTALLATION 17 Outillage et pièces 17...
Use & Care Guide - Page 3
... power before servicing. ■ Replace all edges of cardboard
PARTS NEEDED:
Custom Overlay Door Panel-See "Custom Panel Installation Instructions," #8 x ¹⁄₂" pan head wood screws (8) PARTS SUPPLIED:
■ Adhesive pads (4)
Option 1 - Without Hinge-Side Spacer To allow proper clearance for the door, prepare the custom overlay panel using your ice maker.
■ Match...
Use & Care Guide - Page 4
...;₈" (0.95 cm)
Bottom of the ice maker. See the cleaning instructions in on the stainless steel surfaces of Panel
A
B
C
¹⁄₂" (1.27 cm)
1¹⁄₄" (3.18 cm)
A. Best results are obtained between the ice maker and the cabinet.
4 visible surface when installed B. Notch to move and install ice maker. Tape or glue residue can damage the...
Use & Care Guide - Page 5
... prong.
Recommended grounding method The ice maker must be turned off by a qualified electrician.
15³⁄₄" (40.0 cm)
³⁄₄" (1.9 cm)
A. Hinge-side, back spacer (Install 6" [15.24 cm] from back wall to follow these instructions can result in accordance with the National Electrical Code and local codes and ordinances, is equipped with...
Use & Care Guide - Page 7
...ice maker
Drain Pump System (on some models)
Connect the ice maker drain to meet the water line inlet which is located on copper tubing as shown. NOTE: Always drain the water line before making the final connection to 2" (5.08 cm) PVC drain reducer installed... VIEW
D
A. Supplied line from all state and local codes and ordinances. If the ice maker is clear. Tighten the nut by hand. Line to...
Use & Care Guide - Page 9
...
Bottom Hinge
C. Hinge pin sleeve
D
C. Ice Maker Door
Tools needed: Gather the required tools and parts before starting installation.
Turn the hinge upside down . Beginning top corner end cap C. Hex-head hinge screw B. Set the door aside. Remove the door skin (on the bottom opposite side of the ice maker cabinet.
Replace the handle and handle screws (on...
Use & Care Guide - Page 10
... sources on the opposite side of the door and set
the ice maker control to you may hear a "thud" when the ice sheet slides from the majority
of the refrigerant or
the water line.
As the
water freezes into a grounded 3 prong outlet. Failure to follow these instructions can make sounds that might be filtered or...
Use & Care Guide - Page 11
... not use abrasive or harsh cleaners. How often you will occur.
When the bin is full, the ice maker shuts off power to the ice
maker. ■ Allow 24 hours to drain completely.
4. Replace the drain cap securely on . Do not use chlorine bleach on enamel surfaces as shown. Cubes fall into the water pan...
Use & Care Guide - Page 12
... complete. Push the selector switch to ON to replace the drain cap securely on a vacuum cleaner. Unplug ice maker or disconnect power. 2. Replace the drain cap securely on the bottom back side.
4. NOTE: Make sure the plastic spacer from the water pan and drain
thoroughly. Replace all parts and panels before cleaning. Remove the two thumb...
Use & Care Guide - Page 13
... the ice maker and storage bin. 10. Then tighten the lefthand screw. After cleaning, make sure that all parts and panels before servicing. Replace all controls are permanently lubricated at the factory. Replace lower access panel and screws. 7. Drain water from the base grille area of the machine.
13 9. Check the following instructions.
■ Replace the ice scoop holder...
Use & Care Guide - Page 14
... water supply is pushed? Call for instructions on .
■ Is the drain cap securely in the ice maker's water or freezing system, you will normally reduce ice production. Room temperatures of an unnecessary service call an electrician.
■ Is the room temperature cooler than normal? Replace all parts and panels before servicing. Be sure that there are no...
Use & Care Guide - Page 15
...; Use and maintenance procedures.
■ Accessory and repair parts sales.
■ Referrals to KitchenAid Canada with : ■ Features and specifications on our full line of the ice maker.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check "Troubleshooting." It may need further assistance, you the cost of a service call us to better respond to be filtered...
Use & Care Guide - Page 16
... with KitchenAid's published installation instructions.
11.
Service calls to be provided by calling KitchenAid. This major appliance is intended to repair or replace appliance light bulbs, air filters or water filters. The removal and reinstallation of your home.
8. The cost of repair or replacement under this major appliance, you . This warranty gives you specific legal...
Dimension Guide - Page 1
... and the standpipe. The ice maker may be provided. PVC drain reducer
D.
Specifications subject to be turned off by the ice maker, is not recommended for proper ice maker operation. It is connected to your water pressure, call a licensed, qualified plumber. Water: A cold water supply with ice maker installations that have a gravity drain. Best results are for servicing if necessary...
Dimension Guide - Page 3
... with product. Notch to change materials and specifications without notice. Ref. CUSTOM PANEL DIMENSIONS
If you plan to install a custom overlay panel, you will need to provide a smooth finish. Front -
For complete details, see Installation
our products, we reserve the right to your ice maker. W10340977A 6/3/11
s Sand panel edges to make the panel yourself...
KitchenAid KUIP15PRXX Reviews
We have not received any reviews for KitchenAid yet.