Kenwood UBZ-LJ8 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood UBZ-LJ8 manuals!
Problems with Kenwood UBZ-LJ8?
Ask a Question
Free Kenwood UBZ-LJ8 manuals!
Problems with Kenwood UBZ-LJ8?
Ask a Question
Popular Kenwood UBZ-LJ8 Manual Pages
User Manual - Page 2
... PREPARATION 5 INSTALLING/ REMOVING BATTERIES 5 SETTING THE ANTENNA 6 INSTALLING/ REMOVING THE BELT CLIP 7 INSTALLING/ REMOVING OPTIONAL ACCESSORIES 8 GETTING STARTED 9 GROUP MODE 10 SECRET MODE 11 MENU SETTINGS 12 BEEP ...25 SPECIFICATIONS 26 TRANSCEIVER SPECIFICATIONS 26 CHANNEL FREQUENCY CHART 26 GROUP MODE NUMBERS 27 TK-3101 / UBZ-LJ8 COMPATIBILITIES 27 TROUBLESHOOTING GUIDE 28
User Manual - Page 3
... vehicles. you can choose from eight preset channels to keep in on your kit before discarding the packing material:
• Transceiver • Belt clip • Instruction manual • Warranty card
1 Your KENWOOD PMR446 is a precision device. You can talk with others listen in touch without the need for purchasing this...
User Manual - Page 4
... in excessively dusty, humid, and/ or wet areas, nor on fuel or while parked in gasoline service stations.
• Do not operate your transceiver or charge your battery pack in an explosive atmosphere (... etc.).
• If an abnormal odor or smoke is not waterproof.
• Turn OFF your KENWOOD dealer.
2 Do not modify or attempt to adjust the transceiver for any reason.
• Do not...
User Manual - Page 6
... activated (page 14). Appears while the VOX function is deactivated (page 19). Appears when the internal audio amplifier has been activated (page 22). Appears while setting the beep function ON or OFF (page 12). Displays the remaining battery power (page 13).
Appears while receiving a signal or while the squelch is in...
User Manual - Page 8
Battery installation
Battery pack installation Label Contacts
Ribbon
3 Align the battery cover tabs with the slots on the transceiver, hold the cover in place, then latch it... different types. ◆ When you do not use the transceiver for an extended period of
time, remove the batteries from the transceiver.
SETTING THE ANTENNA
Before using the transceiver, be sure to raise the antenna.
6
User Manual - Page 10
...Headset • SMC-32 Speaker-Microphone • SMC-33 Speaker-Microphone • SMC-34 Speaker-Microphone To install these accessories: 1 Open the SP/MIC tabs on the side of the transceiver. 2 Insert the accessory's ...the attached tabs in order to the accessory instruction manuals for detailed
instructions on each of the accessories. ◆ The transceiver is not water resistant while using accessories....
User Manual - Page 15
... display lets you release the PTT switch. High battery power
Medium battery power
Low battery power
Time to replace the batteries or recharge the battery pack
Depending on the display.
1 Enter the Menu Settings (page 12) and press the ▲ or ▼ key until you know approximately how much battery life is...
User Manual - Page 16
...POWER OFF (APO)
Auto Power Off is ignored and scanning continues.
14 One minute before power is set up on the display. When the transceiver verifies a signal on a channel, it proceeds to check whether...warning tone sounds (even if the beep tone has been turned OFF).
1 Enter the Menu Settings (page 12) and press the ▲ or ▼ key until you unintentionally leave the transceiver power ...
User Manual - Page 17
... use the Auto Channel Select function, ensure that it to your transceiver ( ).
3 Press the PTT switch or turn the transceiver power OFF to confirm your setting.
When you have added Auto Channel Select to your transceiver, you can then operate scan while using the Menu...
User Manual - Page 18
...Using the VOX feature, you use an optional headset with excessive ambient noise. With VOX activated, your setting. • If you set the VOX Gain Level ( ) from 1 to 3, where 3 is not so loud that it ... ), the VOX icon appears on a boom that rests in front of this, you must set a VOX Gain Level:
1 Enter the Menu Settings (page 12) and press the ▲ or ▼ key until you reach the ...
User Manual - Page 19
...Gain Level and Delay Time, you can select the delay time as described above.
3 To exit VOX operation, set the VOX Delay Time ( ) from 0.5 to 3.0 seconds.
3 Press the PTT switch or turn the ...transmitted. To avoid this, select an appropriate delay time to allow your entire message to confirm your setting. However, do not need to receive mode too quickly after you stop speaking, the end of your...
User Manual - Page 20
... a Calling Alert Tone to your party members. 3 Continue your call . To select your Calling Alert Tone: 1 Enter the Menu Settings (page 12) and
press the ▲ or ▼ key until you press the ▲ or ▼ key.
4 Press the PTT switch or turn the transceiver ...
User Manual - Page 21
... a call. • When receiving a call without it continuously cutting out. 1 Enter the Menu Settings (page 12) and press the ▲ or ▼ key until you have turned the squelch ...the busy icon appears on the transceiver automatically mutes the speaker so you will reset the squelch to confirm your setting. • If you reach the " " (Squelch) display.
2 Press the key to turn the squelch...
User Manual - Page 25
... hold the ▲ and ▼ keys while turning the transceiver power ON.
•
appears on the display. ("LJ8" is the
transceiver model name.)
3 Release the keys to their default values. Menu Name
Available Settings
Default Ref. Setting Page
Group Mode Number OFF/ 1 ~ 38
OFF 10
Secret Mode
OFF/ ON
OFF 11
Loudness
OFF/ ON...
Kenwood UBZ-LJ8 Reviews
Do you have an experience with the Kenwood UBZ-LJ8 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!