Kenwood TK-90 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood TK-90 manuals!
Problems with Kenwood TK-90?
Ask a Question
Free Kenwood TK-90 manuals!
Problems with Kenwood TK-90?
Ask a Question
Kenwood TK-90 Videos
Popular Kenwood TK-90 Manual Pages
Operation Manual - Page 1
TK-90
HF TRANSCEIVER
INSTRUCTION MANUAL
TRANSCEPTOR HF
MANUAL DE INSTRUCCIONES
© B62‑1866‑40 (M) 09 08 07 06 05 04
Operation Manual - Page 5
...for choosing KENWOOD for any transceiver.
◆ EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. ... passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will provide dependable communications to configure the transceiver while driving; ...
Operation Manual - Page 6
...CONNECTION 2 MOBILE INSTALLATION 2 INSTALLING THE TRANSCEIVER 2 ANTENNA ...REVIEWING MESSAGES IN THE STACK MEMORY ......... 15 SEND THE GPS DATA 16 MANUALLY SENDING THE GPS DATA 16 GPS POLLING 16 SHORT TEXT MESSAGES 16
ADVANCED OPERATIONS 17 DIRECT CHANNEL 17 SCRAMBLER 17 CHANGING THE SCRAMBLER CODE 17 VOX (VOICE-OPERATED TRANSMIT) SETUP...GUIDE 21 APPENDIX 22
KEY FUNCTIONS 22
ii
Operation Manual - Page 7
... to radio frequency interference with fuses)
Fuse
25 A 4A
Foot pads
Instruction manual
ALE feature operation manual
Part Number Quantity E30-3489-XX 1 F52-0044-XX 1 F52-0038-XX 1 J02-1302-XX 2 B62-1866-XX 1
B62-2001-XX 1
BASE STATION INSTALLATION
FOOT PADS
A set of foot pads are provided so that your antenna system is greater...
Operation Manual - Page 8
...AC outlet until the locking tab clicks.
■ REPLACING FUSES If the fuse blows, determine the cause then correct the problem. After the problem is present while transmitting. Note: The following preparation instructions are correct (Red: positive, Black: negative).
2 Connect the connectorized end of the vehicle.
MOBILE INSTALLATION
Various electronic equipment in your dealer for...
Operation Manual - Page 22
... the key programmed as Selcall to view the Selcall list.
2 Press the CH and keys to select the ID of 48
characters.
16
GPS POLLING
If your transceiver receives a GPS Polling request, it will automatically transmit your GPS data. SEND THE GPS DATA
If a GPS unit has been installed and is set up by...
Operation Manual - Page 23
...
If your dealer has installed an optional scrambler board, you have begun speaking into transmit mode due to select the memory channels they have the same scrambler code set scrambler code on their transceivers. When activated, the transceiver distorts your calls.
VOX (VOICE-OPERATED TRANSMIT) SETUP
VOX eliminates the need of the transceiver to switch into the microphone...
Operation Manual 1 - Page 1
... calls • All calls • AMD messages • GPS data * (requires a GPS receiver) • Emergency calls * • Soundings
* ALE is found, the transceiver enters standby mode. HF Transceiver
TK-90
ALE FEATURE OPERATION MANUAL
© B62-2001-10 09 08 07 06 05 04 03 02 01
CONTENTS
INTRODUCTION...1 FEATURES...1 BASIC OPERATIONS ...1 ALE OPERATION MODE...2 INDIVIDUAL...
Operation Manual 1 - Page 2
...you can transmit by pressing the CH / keys, and you can manually select an ALE channel by pressing the
PTT switch. When a link ...programmed as ALE to enter the ALE Call menu.
2 Press the CH / keys to select your dealer to GPS Data Input, to select GPS CALL.
4 These menus cannot be selected when ALE operation mode is set by your desired ALE Call menu item. Additionally, the TK-90 can be set...
Operation Manual 1 - Page 3
...of the display. Receiving a Net Call
When the TK-90 receives a Net call to all members within the...message.
• List numbers m1 to m10 are pre-programmed messages.
• You can enter your own message {...manually scroll the message by using the keys.
• To return to the address selection mode without sending a message, press the A key.
6 Optional: If you want to select a specific...
Operation Manual 1 - Page 4
... link is received, the transceiver will automatically terminate the link. DIRECT CALLS
Up to 4 keys can be programmed with the Direct Call feature, allowing you to easily make individual calls to those stations which a link can be terminated: automatically and manually. When the programmed GPS report interval time passes, the TK-90 automatically transmits the GPS...
Operation Manual 1 - Page 5
... the message.
• If there are also set by your dealer.
2 To exit Emergency mode, press and hold the key programmed as normal.
A maximum number of cycles, Emergency mode will automatically end and the transceiver will change to the channel that was entered.
You can also manually scroll the message by using the keys...
Operation Manual 1 - Page 6
...transceiver moves to the next channel in the stack for deletion.
• A confirmation message appears on the display.
• To cancel the operation, press the key. Manual Sounding
Manual Sounding can be used only in the network's scan list.
EXCHANGING THE LQA SCORE
1 Press the key programmed...When the programmed interval passes, the TK-90 automatically transmits the ...
Operation Manual 1 - Page 7
... key programmed as either 12 or 24 hour time.
11 Press the ■ key to save the setting and move to the minute setup. • "MINUTE" appears on the display.
4 Press the CH / keys to select the current month (from 00 to exit. Refer to the TK-90 instruction manual for details on how to hear your transceiver settings...
Kenwood TK-90 Reviews
Do you have an experience with the Kenwood TK-90 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!