Kenwood TK-D240V Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood TK-D240V manuals!
Problems with Kenwood TK-D240V?
Ask a Question
Free Kenwood TK-D240V manuals!
Problems with Kenwood TK-D240V?
Ask a Question
Popular Kenwood TK-D240V Manual Pages
User Manual 1 - Page 10
... transmit power to lock/unlock the transceiver keys.
Release this key to immediately select your home channel (pre-programmed by your PTT ID list, to set the current channel as the Home Channel. n Priority-channel Select Press this key to request a call.
On high transmit power channels, press this key.
While...
User Manual 1 - Page 12
...Repeat step 2 for Selector positions 2 ~ 4. • If there are less than 4 password digits, repeat for only the number of channels.
2 Select the desired channel using the Selector ...of digits the password contains.
4 Press the PTT switch to confirm the password. • When the correct password is programmed with settings for transmitting and receiving. Transceiver Password
If your transceiver...
User Manual 1 - Page 13
...an individual call The Transceiver Password function is low while transmitting Scanning
Receiving an encoded call and the received group ID matches the ID set the LED to blink either... approximately 1.5 inches (3 cm to the call only if the received signal matches your transceiver settings.
If signaling has been programmed on your mouth. Receiving Group Calls
When you will sound. To...
User Manual 1 - Page 14
...hands-free. VOX can be turned off for specific channels by your dealer. To activate VOX and set the VOX Gain level, from 1 (least...are using a supported headset. When turned ON, a beep sounds. When turned OFF, a double beep sounds.
5 Press the PTT switch to save the setting. •...
VOX operation allows you will be unable to enter VOX setup
mode. ◆◆ If a headset is connected to...
User Manual 1 - Page 16
...is received on that channel.
However, when scanning is ended and
restarted, the Scan settings return to add/remove channels).
16 While scanning, the transceiver checks for signals on ... transceiver will automatically change to the scanning sequence. SCAN DELETE/ ADD
You can temporarily remove specific channels from your scan list. 1 Select your desired zone and/or channel. 2 Press ...
User Manual 1 - Page 17
...emit a tone and automatically enter Emergency operation. Lone Worker Mode
Lone Worker Mode is set the transceiver to emit tones and received signals as [Lone Worker] to toggle the Lone... as normal, or
mute the speaker during Emergency operation. Note: ◆◆ Your dealer can set the transceiver to emit a tone when transmitting in Emergency
mode. ◆◆ Your dealer can ...
User Manual 1 - Page 19
... list number. Receiving
When you can being the call and the received group ID matches the ID set up with the ID list number you wish to call, then press the PTT switch to start ...press the key programmed as [Paging Call]. • If PTT Proceed tone is 10 seconds). DMR
DMR is set up on a DMR digital channel. After the tone ends, you respond to the call by sending and receiving digital...
User Manual 1 - Page 20
...is received or an operation is released and the LED indicator blinks red when the battery needs recharged or replaced. Release the PTT switch to stop the tone. LOW BATTERY WARNING
While operating the transceiver, the Low...receiving a QT/
DQT signal which does not match the QT/DQT tone/code set up in your dealer for an explanation on a channel that is already in use , a warning tone will ...
User Manual 4 - Page 3
For using details instruction manual (User Manual), refer to your radio. Ask your radio. http://manual.kenwood.com/en_contents/search/keyword VHF DIGITAL TRANSCEIVER
TK-D240
UHF DIGITAL TRANSCEIVER
TK-D340
USER GUIDE
This User Guide covers only the basic operations of your dealer for information on any customized features they may have added to the following URL.
User Manual 4 - Page 5
...installation. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the instructions, may cause harmful interference to Part...are expressly approved by the party responsible/ JVC KENWOOD. The user could lose the authority to ...service to
which can generate radio frequency energy and, if not installed and used in accordance with ...
User Manual 4 - Page 7
... service stations. • Near explosives or blasting sites. • In aircraft. (Any use of the transceiver must follow the
instructions ... your country or region. Do not touch these locations when replacing the battery pack. • Do not immerse the transceiver ...specified by KENWOOD. • If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts. •...
User Manual 4 - Page 11
... pack is deformed, or seems abnormal for longer than the specified time! Electrolyte leaking from battery can easily catch on fire and may cause eye-problems.
WARNING • Do not charge the battery for any other reason, remove it from flammable areas. If left untreated, it . The battery may generate heat...
User Manual 4 - Page 14
... not exist. • Selecting a channel which does not exist causes a continuous error
tone to sound. 1 Set the Channel selector to channel 1, then pull the Channel
selector knob off the transceiver... is not positioned at channel 1, the knob may
not install correctly and the channel may be unable to change. 2 Insert the channel stopper. 3 Set the arrow of the Channel stopper to the highest channel
...
User Manual 4 - Page 20
... using the key programmed as [Monitor] or [Squelch Off] to
check whether or not the channel is free. • If the channel is programmed with settings for transmitting and receiving.
Release the PTT switch to switch the transceiver ON. BASIC OPERATIONS
Switching Power ON/OFF
Turn the Power switch/ Volume control...
User Manual 4 - Page 21
...
Indicator Color
Meaning
Lights red
Transmitting
Lights green Lights blue
Receiving a call
The Transceiver Password function is low while transmitting
Blinks green
Scanning
Blinks orange or blue *
Receiving an encoded...selected channel, you receive a group call and the received group ID matches the ID set the LED to the call only if the received signal matches your transceiver, you ...
Kenwood TK-D240V Reviews
Do you have an experience with the Kenwood TK-D240V that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!