Kenwood TK-8360H Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-8360H manuals!
Problems with Kenwood TK-8360H?
Ask a Question
Free Kenwood TK-8360H manuals!
Problems with Kenwood TK-8360H?
Ask a Question
Popular Kenwood TK-8360H Manual Pages
Instruction Manual - Page 3
ENGLISH
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
TK-7360H/ TK-8360H TK-7360HV/ TK-8360HU
INSTRUCTION MANUAL
Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for JVC KENWOOD Corporation.
Instruction Manual - Page 5
... instructions, may cause harmful interference unless the modifications are carried in a residential installation.
One or more of any customized features they are expressly approved in gasoline service ... parked in the instruction manual. Do not transmit while the caps are grateful you are transporting blasting caps in your mobile radio.
This instruction manual covers only the...
Instruction Manual - Page 6
... OPERATIONS 15 BACKGROUND OPERATIONS 18 VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT 19
ii
Please check
and observe the vehicle regulations in your Kenwood dealer. • Use of the transceiver while...the transceiver while driving; For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in 12 V negative...
Instruction Manual - Page 7
... A fuse 2 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Microphone (with cable) • KMC-30 (TK-7360H/ TK-8360H 1 • KMC-35 (TK-7360HV/ TK-8360HU 1 Microphone hanger (with the carrier immediately. GETTING STARTED
Note: The following instructions are not properly protected...
Instruction Manual - Page 8
...replace a fuse with one that is sufficient space at the rear of the transceiver for servicing while keeping the power applied.
■ Installing the Transceiver
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set... drilling mounting holes, be careful not to damage vehicle wiring or parts.
1 Mark the position of the holes in a place where they...
Instruction Manual - Page 10
... GPS position is the Priority channel. Note: If this icon is added to the scan sequence. The selected channel is determined. The current zone is set up for use in the stack memory. The External Speaker function is on . The Operator Selectable Tone function is on . A caller ID/message is added...
Instruction Manual - Page 11
...Status 3 • Stun (MDC-1200) • Talk Around • Telephone Disconnect • Transceiver Password • Voice Memo • Volume Down • Volume Up • Zone Del/Add •...; Zone Up
1 Emergency can be programmed only on the key. When assigned, the dealer must set the key assignment hold to "Enable" and second function as "Emergency".
5 PROGRAMMABLE FUNCTIONS
The ,...
Instruction Manual - Page 13
...selected. TEMPORARY CHANNEL LOCKOUT
During scan, you made a call is ended and
restarted, the Scan settings return to transmit. SCAN
Scan monitors for a signal on which time scan resumes. However, ...you can temporarily remove specific channels from your desired zone and channel. 2 Press the microphone PTT switch and speak into the microphone to normal.
7 If set up to the Priority...
Instruction Manual - Page 15
... configured as "Enabled") or to select an
autodial list number. • You can make DTMF calls, you must use an optional microphone with a DTMF keypad.
MANUAL DIALING
1 Press and hold A or # to delete all digits.
6 Repeat steps 4 and 5 to enter the entire name. 7 Press S to accept the name and enter a number...
Instruction Manual - Page 18
...KENWOOD Corporation. STATUS MESSAGE
Status messages are 2-digit codes... ranging from 10 to select
the ID of FleetSync.
MDC-1200 and FleetSync cannot be reviewed after reception. Each transceiver must have its own Fleet and ID number. A maximum of 15 received messages can be stored in place of the station you can also manually...a call. Note: If set up by programming. SELCALL ...
Instruction Manual - Page 21
... mode, the transceiver will change to the Emergency channel and begin transmitting based on how the transceiver is set up.
2 To exit Emergency mode, press and hold the Emergency key again. • If the ... period of your own group to clearly hear what you are saying. TALK AROUND
During interruptions in service (such as Talk Around to toggle the Talk Around function ON or OFF. • The icon...
Instruction Manual - Page 22
... selection is configured as "Enabled") or to select your
desired scrambler code. 3 Press S, , or to store the new setting.
• After changing your scrambler code, be sure to inform all of your desired squelch level from 0 to 9. 3 Press S or to store the new setting.
Press again to return to normal
operation. • Squelch Off...
Instruction Manual - Page 24
... the PTT switch is active. BUSY CHANNEL LOCKOUT (BCL)
If BCL is sent each channel.
PTT ID
PTT ID is the transceiver unique ID code which is set up by pressing the PTT switch again, immediately after releasing it, when the channel is used with
optional boards.
• The
icon appears on...
Instruction Manual - Page 25
.... icon appears on the display when the Auto Recording function
■ Voice Memos
You can set the transceiver to automatically respond to Individual Calls.
1 Press the key programmed as Auto Reply Message...transceiver for recording, "I am not available. VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT
When using the optional VGS-1 voice guide & storage unit, you gain access to the caller and "MEM...
Instruction Manual - Page 26
...memos. • "RM" represents reply messages.
3 The transceiver will announce the time and channel, then the recording will announce the new setting. (Voice announcements vary by your conversation, "STORE" will appear on the display, otherwise a recording channel with the time of the recording.../group ID. Press and hold A or # to delete the selected recording. VOICE GUIDE
If set up by dealer...
Kenwood TK-8360H Reviews
We have not received any reviews for Kenwood yet.