Kenwood TK-8302HU Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-8302HU manuals!
Problems with Kenwood TK-8302HU?
Ask a Question
Free Kenwood TK-8302HU manuals!
Problems with Kenwood TK-8302HU?
Ask a Question
Popular Kenwood TK-8302HU Manual Pages
Instruction Manual - Page 3
ENGLISH
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
TK-7302/ TK-8302 TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU
INSTRUCTION MANUAL
Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for JVC KENWOOD Corporation.
Instruction Manual - Page 4
... to radio MIC Data Detection
Antenna Connector Impedance is 50 Ω. Pin Name
1
SPO
3
GND
Description External Speaker Output Ground
DC Input Connector
Pin NO. Specification
I/O
13.6 V ʶ15 %
O
Power ON: more than 8V Power OFF: less than 6V
I
4 Ω
O
500 mV p-p
O
5 k Ω
I
High Impedance
I/O
High Impedance
I/O
High Impedance
I/O
High Impedance...
Instruction Manual - Page 5
...comply with the instructions, may have chosen Kenwood for your mobile radio. This instruction manual covers only the ...installation. THANK YOU
We are grateful you are transporting blasting caps in the instruction manual. If this equipment if an unauthorized change or modification is encouraged to try to correct the interference by fine and/or imprisonment. ◆ Refer service to Part...
Instruction Manual - Page 6
....
◆ Use only the supplied DC power cable or a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in 12...
Instruction Manual - Page 7
...; Flat washer 4 Microphone (with cable) • KMC-30 (TK-7302H/ TK-8302H 1 • KMC-35 (TK-7302/ TK-7302HV/ TK-8302/ TK-8302HU 1 Microphone hanger (with the carrier immediately. If any items are missing or have been damaged during shipment, file a claim with 4 x 16 mm self-tapping screws 1 Instruction manual 1
PREPARATION
Various electronic equipment in your vehicle contains such...
Instruction Manual - Page 8
..., check how far the mounting screws will not interfere with a fuse of the transceiver for servicing while keeping the power applied.
■ Installing the Transceiver
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in a place where they
will extend below...
Instruction Manual - Page 10
...; Paging Call
1 Direct Zone Channel can be programmed only on the S, A, , and 2 Emergency can be programmed only on the display can be programmed to indicate specific modes of operation.
Instruction Manual - Page 11
...on the display. If Squelch Off has been programmed onto a key, you enter an incorrect password, the transceiver remains locked. Press the Volume Down key to decrease the volume. TRANSMITTING/ RECEIVING...5 SELECTING A ZONE AND CHANNEL
Select the desired zone and channel using a keypad, simply enter the password digits and proceed to step 3. 2 Press C> to accept the entered digit and move to the ...
Instruction Manual - Page 12
... at that channel, even if call is no longer scanned. SCAN DELETE/ADD
You can temporarily remove specific channels from your scan list. 1 Select your desired zone and/or channel. 2 Press the key programmed... normal channel. • "P" appears on the display to scan, "cA" appears on dealer setting). To start/stop scanning, press the key programmed as Scan Delete/Add to remove a channel or...
Instruction Manual - Page 13
... of the following types of Scan Revert channels: • Selected: The last channel selected before scan, whichever operation occured latest. MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the desired digits using the keypad.
• If Keypad Auto-PTT is... SCAN REVERT
The Scan Revert channel is no data in the redial memory, an error tone will sound.
3 Press the PTT switch to transmit;
Instruction Manual - Page 14
...OST number. 4 Use the transceiver the same as in a regular call containing a matching DTMF code. OPERATOR SELECTABLE TONE (OST)
You can be pre-programmed by your dealer. 1 Select your ... may also program several types of optional signaling for the selected channel. A QT tone/ DQT code is stolen or lost. When the transceiver receives a call containing matching 2 tones. DTMF Signaling:...
Instruction Manual - Page 15
...speak into the microphone.
■ Identification Codes An ID code is a protocol owned by your PTT List ID, ...switch and begin your conversation.
■ Receiving If enabled by JVC KENWOOD Corporation. To respond to transmit
your dealer, an alert tone will sound...set up by programming. SELCALL (SELECTIVE CALLING)
A Selcall is installed on the display when sending a status message.
Instruction Manual - Page 16
... to toggle the Scrambler function ON or OFF. • "Sr" appears on the display while the Scrambler is set up.
2 To exit Emergency mode, press and hold the Emergency key again. • If the Emergency mode ...transceiver. The built-in scrambler prevent others from easily listening in service (such as Emergency.
• Depending on the display while Talk Around is not operated for details.
Instruction Manual - Page 17
... "co" (code) appears on the display, followed by the current scrambler code. 2 Press to select your desired scrambler code. 3 Press S or to store the new setting.
• After changing your scrambler code, be used ...to select the desired squelch level from 0 to 9. 3 Press S or to store the new setting. MONITOR/ SQUELCH OFF
You can only be sure to inform all of your transceiver's squelch level...
Instruction Manual - Page 18
....
Release the PTT switch. PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is activated. DISPLAY BRIGHTNESS
You can only be unable to transmit if the channel is set up by your dealer for an extended duration. DIRECT ZONE CHANNEL
Press the key...
Kenwood TK-8302HU Reviews
We have not received any reviews for Kenwood yet.