Kenwood TK-790HB Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood TK-790HB manuals!
Problems with Kenwood TK-790HB?
Ask a Question
Free Kenwood TK-790HB manuals!
Problems with Kenwood TK-790HB?
Ask a Question
Popular Kenwood TK-790HB Manual Pages
Instruction Manual - Page 1
INSTRUCTION MANUAL
POWER GRP
TX BUSY
VOL
CH
POWER GRP
TX BUSY VOL
CALL MON SCAN SP OPT A B C OST
MON SCN
CH
VHF FM TRANSCEIVER
TK-690 series
VHF FM TRANSCEIVER
TK-790 series
UHF FM TRANSCEIVER
TK-890 series
© B62-0970-50 (K) 09 08 07 06 05
Instruction Manual - Page 2
... at peak efficiency. We believe this product. THANK YOU! As a result, we feel strongly that you chose KENWOOD for your land mobile applications. MODELS COVERED BY THIS MANUAL
• TK-690H: VHF FM Transceiver • TK-790: VHF FM Transceiver • TK-790H: VHF FM Transceiver • TK-890: UHF FM Transceiver • TK-890H: UHF FM Transceiver
Instruction Manual - Page 3
...generate radio frequency energy and, if not installed and used in a particular installation. This equipment generates, uses and can be...into or are enclosed in the instruction manual.
SAFETY: It is mounted in a gasoline service station. Do not carry spare fuel... receiver is encouraged to try to Part 15 of the transceiver. Note: This instruction manual covers only the basic functions of ...
Instruction Manual - Page 4
...CHECKING EQUIPMENT 1 Supplied Accessories 1
PREPARATION 3 Tools Required 3 Power Cable Connection 3 Installing the Transceiver 4
GETTING ACQUAINTED 5 Basic Front Panel (KCH-10 5 Basic Panel ... Volume 15 Selecting a Group 15 Selecting a Channel 15 Making a Call 15 DTMF CALLS 16 Manual Dialing 16 Redialing 16 Auto Dialing 16 OTHER TRANSCEIVER FUNCTIONS 18 Time-out Timer (TOT 18 Busy...
Instruction Manual - Page 5
... Accessories
Quantity
Item
Part Number
TK-890 (B) TK-890(B) TK-890 TK-790 (B) TK-790 (B) TK-790 TK-690 (B)
H H H
Microphone and microphone cable 1 Microphone hanger Mounting bracket Power cable assembly Fuse (15 A) Speaker short plug Retaining band
Knob
Hex-headed screw Self-tapping screw (5 x 16 mm) Self-tapping screw (4 x 16 mm) Spring washer Flat washer Instruction manual
T91-0587-X5...
Instruction Manual - Page 7
...The following preparation instructions are required ...damage vehicle wiring or parts.
CHECK THE BATTERY POLARITY AND VOLTAGE OF THE VEHICLE BEFORE INSTALLING THE TRANSCEIVER.
1 Check for installing the transceiver:
...hole exists, use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory.
■ Tools Required
Note: Before installing the transceiver, always check how...
Instruction Manual - Page 9
... !1
q POWER switch Press to decrease it. The BUSY (green) indicator lights while the selected channel is set as No Function.
!1 PF5 key 5 Press GRP Down to decrease it. (Alternatively, this connector and secure....
y CH (Channel) control Turn clockwise to increase the channel selection (default setting), and counterclockwise to decrease the group selection by one step. (See page 11...
Instruction Manual - Page 10
... channel is in the scanning sequence if group scan has been set to PA speaker.
P2 indicates a Priority 2 channel; Appears during and after transmitting if set to "Multi" (please consult your dealer for setting the scan). Appears when the selected group is set by DTMF or 2-Tone signaling.
Appears when Aux A is enabled. Appears...
Instruction Manual - Page 12
!2 CH (Channel) control Turn clockwise to increase the channel selection (default setting), and counterclockwise to decrease it. (Alternatively, this control can be programmed with group up/down.)
!3 PF1 key
!4 PF2 key !5 PF3 key !6 PF4 key
Press these PF (programmable function) keys to activate their programmable functions {page 11}. The default is set as No Function.
!7 PF5 key
8
Instruction Manual - Page 13
... if group scan has been set to PA speaker.
Appears during and after transmitting if set to "Multi" (please consult your dealer for setting the scan). Appears when audio... output is ON. RCL indicates a Recall Channel;
Appears when Aux C is set by DTMF or 2-Tone signaling. ■ Full-featured Panel Display e r t y u i o !0 !1 !2!3
w
CALL MON SCAN SP OPT A...
Instruction Manual - Page 16
...12
OPT (Scrambler)
If you have an optional scrambler board installed in your transceiver, you can press this key to turn it...the DTMF microphone keypad backlight ON or OFF. A tone sounds and CODE appears on the display. When you receive a call (requires ANI... activate. HA (Horn Alert)
Press this key to select the desired setting.
3 Press the OPT key. DIM (Dimmer)
Press this key to...
Instruction Manual - Page 17
... tone from the pre-programmed QT/DQT list. When a signal is in the scanning sequence, an error tone sounds.
To enter carrier squelch scan, press the MON key while scan is received while scanning,...activate scan whether the microphone is less than a single channel. ON HOOK requires the microphone to be set up two different ways: ON HOOK or OFF HOOK. A tone sounds.
2 Press the GRP Up...
Instruction Manual - Page 18
.... A tone sounds and the display returns to the normal channel. TA (Talk Around) Press this key to switch between "Internal" and "External" speaker. You can manually adjust the squelch level using this function while scanning and receiving a call without using a repeater. This function is selected, a tone sounds and the SP icon...
Instruction Manual - Page 20
...DTMF CALLS
You can make DTMF calls using the optional KMC-28 DTMF microphone. ■ Manual Dialing
To dial a number manually: 1 Press and hold the PTT switch, then press 2, 5, 8, 0, , or ... A maximum of 16 digits can be erased.
■ Auto Dialing
Note: Auto dialing is either manually or automatically, will be redialed. The last number dialed, either enabled or disabled by pressing a DTMF...
Instruction Manual - Page 22
... following functions can be using the same channel as you. When the transceiver receives a correct code, the CALL icon flashes. If alert tone has been enabled, an alert tone sounds after receiving the 2-Tone/ DTMF signal. To set a Priority2 channel, press and hold the SCN key, then press the MON key 3 times...
Kenwood TK-790HB Reviews
Do you have an experience with the Kenwood TK-790HB that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!