Kenwood TK-785 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-785 manuals!
Problems with Kenwood TK-785?
Ask a Question
Free Kenwood TK-785 manuals!
Problems with Kenwood TK-785?
Ask a Question
Popular Kenwood TK-785 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
TK-785/ TK-885
KENWOOD CORPORATION
© B62-1434-00 (E) 09 08 07 06 05 04 03 02 01 00
Operation Manual - Page 2
...is in advanced technology. Models Covered by this Manual
• TK-785: VHF FM Transceiver • TK-885: UHF FM Transceiver...IS PUNISHABLE BY FINE AND/OR IMPRISONMENT. ◆ REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. to preven
overheating, do not ...remove the power input
connector from the container.
Contact your KENWOOD dealer. • Continuously transmitting for over 1 minute. i...
Operation Manual - Page 4
... washer (4 pieces)
Instruction manual
Part Number T91-0624-XX T91-0621-XX
J19-1584-XX
J29-0627-XX E30-3438-XX F52-0006-XX B09-0235-XX
Quantity 1
1 1 1 1
N99-0395-XX
1
B62-1434-XX
1
Microphone (TK-785 E only)
Microphone (TK-885 K only)
Microphone hanger
Mounting bracket
Power cable assembly Speaker jack cap
Screw set 1 Carefully unpack the...
Operation Manual - Page 5
...THE RADIO FREQUENCY ENERGY WHICH IS PRESENT WHILE TRANSMITTING.
The following preparation instructions are required for installing the transceiver: • 6 mm (1/4 inch) or larger electric ...with a retaining band.
• Be sure to damage vehicle wiring or parts. Note: The following tools are for the 4 x 16 mm self-...KENWOOD dealer, an authorized KENWOOD service facility, or the factory.
Operation Manual - Page 6
... into the mounting bracket and secure it using the supplied hex-headed screws.
4 Mount the microphone hanger, using the mounting bracket as a template. Installing the Transceiver
FOR PASSENGER SAFETY, INSTALL THE TRANSCEIVER SECURELY, USING THE SUPPLIED MOUNTING BRACKET, SO THE TRANSCEIVER WILL NOT BREAK LOOSE IN THE EVENT OF A COLLISION.
1 Mark the...
Operation Manual - Page 7
... !0 D key !1 CALL key
4 Front Panel
qw e
r
t y u i o !0 !1
q (DC Source) switch Press to increase and decrease the volume.
THE BASICS
Note: Features listed in this manual. w Transmit/ Receive indicator e / (Volume) keys
Press these keys to switch the transceiver ON (or OFF).
Mode specific features can be found in their corresponding sections in this connector.
Operation Manual - Page 9
... as the external foot switch, can be programmed onto certain keys. u A key (default setting: Status/ Stack) Press to activate its auxiliary function {below}. Also press to scroll right...Press to activate its auxiliary function {below . Note: Some of these functions.
i B key (default setting: Redial) Press to end the current call address.
Contact your dealer for details.
• AUX ...
Operation Manual - Page 10
...Channel
After switching the power ON, press any key while the power on how your dealer sets up the transceiver.
Appears while there is displayed to start searching for a control channel ...
Note: Icons not described above are listed in Trunking mode. All messages described in this manual are not used while in English.
Or, wait for 2 seconds to allow the transceiver...
Operation Manual - Page 11
...the call. If the call time expires before you press the key, the call will be set up to either count up (increasing number) or count down (decreasing number).
4 Press the... appears on the display before returning to the appendix {page 15} for the available dial strings and control codes. 2 Initiate the call, depending on page 10). A single triangle (▲) represents low power while dual...
Operation Manual - Page 12
Refer to the appendix {page 15} for the available dial strings and control codes.
2 Press the Status/ Stack key (default is the A key), then press the / (...on the main display and "CAL" appears on the 3-digit sub-display. • If you have the caller's address set up in your transceiver, the call address is programmed in the transceiver memory. PSTN: A call from a PSTN telephone system....
Operation Manual - Page 13
...; Fail: The control station received an invallid call . Sys Busy: The system is currently busy. No Reply: The called party has been called party has set their transceiver to "Viewing the Stack", below. Queued: All communication channels are currently in another call. NU: You entered an invallid call address. your status...
Operation Manual - Page 14
... before returning to the previously selected call address.
4 To end the call diversion, enter control code "#44" with the microphone keypad, press the microphone key, enter the unit number of the...is being processed, "Holding" appears on the display. While your request is set , "Complete" momentarily appears on the display before returning to the previously selected call address.
■...
Operation Manual - Page 15
... selected channel. Appears while you are listed in order to turn Scan ON (or OFF).
u A key Press to select your dealer sets up the transceiver. All messages described in this manual are monitoring a channel by pressing the CALL key.
r / (Control) keys Press these keys to turn the squelch OFF in English. Display...
Operation Manual - Page 16
... on how your transceiver is programmed, you can return to Trunking mode in one of three ways: Manual: Press the key to change the operating mode. Conventional Mode Operation
1 Press the / (control)... how your transceiver is programmed, you can enter Conventional mode in one of two ways: Manual: Press the key programmed as Conventional to change the operating mode. When it to Conventional ...
Operation Manual - Page 18
...
Individual number Group number
20 ~ 89 90 ~ 99
Dial String
3 Digit Dialing Function
Individual number Group number Emergency operator Enter the open channels
Network operator services
Dial String 200 ~ 899 900 ~ 998 112, 999 101 ~ 110 100, 111, 121, 131, 141, 151, 161, 171, 181, 191
4 Digit Dialing PABX call
Function...
Kenwood TK-785 Reviews
We have not received any reviews for Kenwood yet.