Kenwood TK-7302HV Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-7302HV manuals!
Problems with Kenwood TK-7302HV?
Ask a Question
Free Kenwood TK-7302HV manuals!
Problems with Kenwood TK-7302HV?
Ask a Question
Popular Kenwood TK-7302HV Manual Pages
Instruction Manual - Page 3
ENGLISH
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
TK-7302/ TK-8302 TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU
INSTRUCTION MANUAL
Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for JVC KENWOOD Corporation.
Instruction Manual - Page 4
...100 mA
O
Max 3A
O
Max 3A
O
Ground
−
Notes
Specification
I/O
4 Ω
O
Ground
−
Notes
Specification
I/O
13.6 V ʶ15 %
I
Ground
I
Notes
Specification
I/O
−
O
13.6 V ʶ15 %
O
Ground
&#...Ground MIC Signal Input Hook / PC Serial Data to radio MIC Data Detection
Antenna Connector Impedance is 50 Ω. Pin Name
1
SPO
3
GND
Description ...
Instruction Manual - Page 5
... antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from the container.
Turn OFF your mobile radio. However, there is no guarantee that to provide reasonable protection against harmful interference in a particular installation. One or more of the FCC Rules. This instruction manual...
Instruction Manual - Page 6
... area. • Do not use options not specified by Kenwood.
◆ The transceiver operates in the event of the transceiver while you are driving may be against traffic laws.
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in 12...
Instruction Manual - Page 7
...1 • 10 A fuse (TK-7302/ TK-8302 2 • 15 A fuse (TK-7302H/ TK-7302HV/ TK-8302H/ TK-8302HU 2 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Microphone (with cable) • KMC-30 (TK-7302H/ TK-8302H 1 • KMC-35 (TK-7302/ TK-7302HV/ TK-8302/ TK-8302HU 1 Microphone hanger...
Instruction Manual - Page 8
... is sufficient space at the rear of the transceiver for servicing while keeping the power applied.
■ Installing the Transceiver
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will extend below the surface. When replacing the fuse in the DC power cable, be careful not...
Instruction Manual - Page 9
...the microphone plug into this jack.
ᶉ Status Indicator Lights during a specified mode, based on dealer programming.
ᶊ S / A / / keys Press to activate their programmable functions {page 4}.
ᶋ... this switch, then speak into the microphone to call a station.
ᶍ Antenna connector Connect the antenna to this connector.
ᶎACC connector Connect the ACC to this connector, via...
Instruction Manual - Page 10
The left and right dots on the display can be programmed only on the S, A, , and 2 Emergency can be programmed with the functions listed below .
• AUX
• Scan Delete/Add...; Zone Up
• Paging Call
1 Direct Zone Channel can be programmed only on the key. PROGRAMMABLE FUNCTIONS
The , , , , S, A, , and keys can be programmed to indicate specific modes of operation.
Instruction Manual - Page 12
...8226; "P" appears on the display to normal. However, when scanning is ended and
restarted, the Scan settings return to indicate the Priority channel (depending on the display.
6 When it is removed,
"cd" ...SCAN DELETE/ADD
You can temporarily remove specific channels from your scan list. 1 Select your desired zone and/or channel. 2 Press the key programmed as Scan Delete/Add to remove a...
Instruction Manual - Page 13
...~ 9). 3 Press the PTT switch to make DTMF calls, you press the PTT switch to quickly call . MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the desired digits using the keypad.
• If Keypad...channel is no data in the redial memory, an error tone will sound.
3 Press the PTT switch to make the call.
REDIALING
1 Press the key programmed as Autodial or the microphone key.
• "...
Instruction Manual - Page 14
... Selectable Tone or press and hold
the microphone key. • "ot" appears on your transceiver receives a call with a revive code. • "St" appears on page 9. OPTIONAL SIGNALING
Your dealer may have programmed QT or DQT signaling on the display, followed by the current OST number. 3 Press to the preset encode and decode...
Instruction Manual - Page 15
...-1200 and FleetSync cannot be limited by JVC KENWOOD Corporation. To respond to 99 (80 ~ 99 are 2-digit codes ranging from 10 to the call .
GPS REPORT
If a GPS unit (NMEA-0183 format) is a protocol owned by programming.
Note: If set up by pressing the keys programmed as Send the GPS data to send your...
Instruction Manual - Page 16
...service (such as a power failure), you can continue to communicate by using the scrambler, all members must hold the Emergency key will vary.
• When the transceiver enters Emergency mode, the transceiver will change to the Emergency channel and begin transmitting based on how the transceiver is set...calls. 1 Press and hold the key programmed as Scrambler to communicate directly with the ...
Instruction Manual - Page 17
.... Release to return
to normal operation.
■ Squelch Level If a key has been programmed as Squelch Level, you can program a key with different scrambler codes. The scrambler function will not work with transceivers set up with one of the new code so they can only be sure to inform all of your group members of...
Instruction Manual - Page 18
.... PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is already in use.
Release the PTT switch. DIRECT ZONE CHANNEL
Press the key programmed as Display Brightness. BUSY CHANNEL LOCKOUT (BCL)
If BCL is set up by your dealer for a channel, the compander will...
Kenwood TK-7302HV Reviews
We have not received any reviews for Kenwood yet.