Kenwood TK-5930 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood TK-5930 manuals!
Problems with Kenwood TK-5930?
Ask a Question
Free Kenwood TK-5930 manuals!
Problems with Kenwood TK-5930?
Ask a Question
Popular Kenwood TK-5930 Manual Pages
User Manual - Page 3
...
• The Bluetooth® word mark and logos are registered trademarks owned by JVC KENWOOD Corporation is under license. VHF DIGITAL TRANSCEIVER
TK-5730
UHF DIGITAL TRANSCEIVER
TK-5830
700/800MHz DIGITAL TRANSCEIVER
TK-5930
USER GUIDE
This User Guide covers only the basic operations of their respective owners. For using details instruction manual (User Manual), refer to your radio.
User Manual - Page 6
..., reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. This voice coding Technology is explicitly prohibited from the transceiver, switch the transceiver
power off before installing the transceiver.
• Use only the supplied DC power cable or a KENWOOD optional DC power cable. • Do...
User Manual - Page 8
...servicing while keeping the power applied.
■ Installing the Transceiver
For passenger safety, install the transceiver securely using the
supplied hex-headed screws. 6 Note: • Before installing...
User guide 1
...set, so the transceiver will extend below the
surface. Check the battery polarity and voltage of the vehicle before installing... hole, then install a rubber grommet...
User Manual - Page 11
... to activate its programmable function.
e Microphone jack
Insert the microphone plug into this jack. The default key setting is [Channel Up]/ [Channel Down]. f TX/RX Indicator
The indicator lights in different colors to the "User Manual" available from the following URL. http://manual2.jvckenwood.com/en_contents/search/
9 For details on programming functions...
User Manual 1 - Page 2
Depending on basic settings. CONTENTS
SCREEN DISPLAY ...3 BASIC OPERATIONS ...4
SWITCHING POWER ON/ OFF 4 ADJUSTING THE VOLUME ...4 TRANSCEIVER PASSWORD 4 SELECTING A ZONE AND CHANNEL 5 TRANSMITTING ...6 RECEIVING ...12 ... BUILT-IN MEMORY 68 INDICATOR LIST ...71
This manual has been prepared based on the setting, the descriptions provided may be different from the actual operations.
2
User Manual 1 - Page 21
... function in the same manner as P25 OTAR.
21 PF Key Menu Analog Conv. p N/A p p p p p p
Zone Up
- Sending of short messages and status messages is not supported.
*4 In P25 Conventional and P25 Trunking systems, Individual + Short Message and Individual + Status function in the same manner as Group. P25 Conv. Sending of short...
User Manual 1 - Page 38
... or delete any DTMF Codes. 1 Press the key programmed as [Autodial] to enter Autodial Mode. Repeat this process to enter Autodial Mode using the [J] and [K] keys, and then set the selected digit by ...using the Menu Mode. ● The first entry in the Autodial list appears on the display. 2 Press the [ ] key to enter manual input mode. 3 Enter ...
User Manual 1 - Page 42
... Encryption keys. ● Turning the transceiver power OFF and the ON again will not be recovered. 3 Press the [ ] key to set up), press and hold
the [ ] key for entering an incorrect password.
42 Alternatively, press the key programmed as [Key Delete] to confirm and exit Key Delete Mode. Note: ● To restore...
User Manual 1 - Page 43
...) these calls. Press this key again to activate the OST function.
When a channel is set up your calls if they set up their transceiver with a QT tone or DQT code, squelch will not hear the call. After selecting and setting up with a RAN, squelch will only open when a call containing a matching RAN is made...
User Manual 1 - Page 50
...you want to call. ● If Manual Dialing is enabled, you can respond to...a Selcall is received. o Identification Codes An ID code is available only in all units ...; Enter a Fleet number followed by JVC KENWOOD Corporation. FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION...digits to select a digit, then press the [ ] key to set the digit and move the cursor to enter Selcall Mode. Alternatively,...
User Manual 1 - Page 51
...Stamp
51 When using the microphone keypad
or the [J]/[K] key.
A maximum of your dealer settings, when the stack memory is full, either the oldest message will be erased when a new...keys to select the station you want to transmit. ● If Manual Dialing is enabled, you want to initiate the call . ● If Manual Dialing is received. o Transmitting 1 Select your talk group. Depending...
User Manual 1 - Page 52
... are displayed the same as [Send the GPS Data], or by your dealer for one second. If set up by accessing the Menu {p. 14} .
LONG MESSAGES
To send and receive long messages, you must...can contain a maximum of 32 Status calls and short messages can be manually transmitted by pressing the key programmed as Status messages and are stored in the stack memory. A combined maximum ...
User Manual 1 - Page 54
... TIMER (TOT)
The Time-out Timer can be programmed only for specific analog channels. It is not used to prevent any caller from using.... If you may have to wait for an extended period of service range (Appears on NXDN Trunking and P25 Trunking channels only)
COMPANDER...they are expanded when they arrive. ● Your dealer must set the compander for both the transmit side and the receive side ...
User Manual 1 - Page 59
... registered to your transceiver will connect to the Bluetooth headset.
If the headset cannot be used automatically, connect manually using the My Device setting in the Bluetooth menu of the transceiver. (Some headset models cannot be used automatically with the transceiver the next time the transceiver and headset are powered on the Bluetooth...
Kenwood TK-5930 Reviews
Do you have an experience with the Kenwood TK-5930 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!