Kenwood TK-5820 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood TK-5820 manuals!
Problems with Kenwood TK-5820?
Ask a Question
Free Kenwood TK-5820 manuals!
Problems with Kenwood TK-5820?
Ask a Question
Popular Kenwood TK-5820 Manual Pages
User Manual - Page 2
MIC Signal Input Ground Serial Data Output Serial Data Input Ground Ground MIC Ground
Specification
I
-
-
- O
I /O
CMOS
O
13.6 V
O
Ground
- ENGLISH
VHF P25 TRANSCEIVER/ UHF P25 TRANSCEIVER
TK-5720/ TK-5820
Instruction Manual
Terminal Description
Microphone Jack
Pin NO. Pin Name 2 RXD1 3 TXD1
Description Serial Data Input Serial Data Output
5 DI
Data Input
6 MI2 7 GND 9 TXD2 10 ...
User Manual - Page 3
...service to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into or removed from attempting to qualified technicians only. This instruction manual...Operating the transceiver within 500 feet (150 m) of copyrights for firmware embedded in Kenwood product memories are reserved for information on any transceiver.
◆ ...
User Manual - Page 4
...instruction manual. The user could lose the authority to operate this equipment does cause harmful interference to radio or television reception, which the receiver is encouraged to try to Part... of the vehicle before installing the transceiver.
◆ Use only a Kenwood optional DC power cable.... safety, install the transceiver securely using an optional mounting bracket and screw set so the...
User Manual - Page 6
... • Flat washer 4 Instruction manual 1
If any items are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory.... Supplied Accessories
Microphone (with cable 1 Microphone hanger (with 4 x 16 mm self-tapping screws 1 DC power cable 1 • Fuse (15 A 2 Mounting bracket 1 Screw set...
User Manual - Page 7
...parts. Note: The following tools are required for installing the transceiver: • 1/4 inch (6 mm) or larger electric drill • 5/32 inch (4.2 mm) drill bit for servicing while keeping the power applied.
Check the battery polarity and voltage of the vehicle before installing the transceiver.
◆ Use only a Kenwood.... The following preparation instructions are for an existing...
User Manual - Page 13
... prevent you will also appear on your transceiver settings. If the Network Access Code matches and the squelch type is set up on the display. Refer to code your mouth.
■ Making Group Calls (... calls. For these channels, simply press and hold the microphone PTT switch to make calls to specific persons. 1 Press the key programmed as Individual.
2 Press / to select a unit ID/name...
User Manual - Page 19
...microphone PTT switch and speaking into the microphone.
■ Identification Codes An ID code is a combination of your transceiver.
14
Each transceiver has ...and "ALL" ID to make an individual call by Kenwood Corporation. The calling station's ID will automatically enter ... Status messages range from 10 to call.
• If Manual Dialing is a voice call ).
A maximum of 15 received...
User Manual - Page 20
...mode (proceed to step 3).
3 Press / to select the station you want to call. • If Manual Dialing is enabled, you can enter a station ID by using the microphone keypad.
4 Press to enter ... to select the status you want to transmit. • If Manual Dialing is enabled, you must connect the transceiver to the transceiver. If set up by using the microphone keypad.
6 Press the microphone PTT ...
Operation Manual - Page 3
O
I
- VHF P25 TRANSCEIVER
TK-5720
UHF P25 TRANSCEIVER
TK-5820
INSTRUCTION MANUAL
Terminal Description
Microphone Jack
Pin NO. High Impedance/ CMOS
I/O
Ground
-
600 Њ
I
High Impedance
I
High Impedance
I/O
Notes
Specification RS-232C compatible RS-232C compatible
CMOS
600 Њ Ground TTL TTL Ground Ground Ground
I/O
Notes
I
O
input : 0.5 V p-p (Typ.) I Data ...
Operation Manual - Page 4
.... Firmware Copyrights The title to the operation of dynamite blasting caps may have been posted.
SAFETY: It is important that the operator is protected by fine and/or imprisonment. ◆ Refer service to your dealer for JVC KENWOOD Corporation. Turn OFF your NEXEDGE mobile radio. Ask your radio.
This voice coding Technology is licensed...
Operation Manual - Page 5
...install the transceiver securely using an optional mounting bracket and screw set so the transceiver will not occur in the event of a collision. This equipment generates, uses and can be against harmful interference in accordance with the limits for technical assistance. Please check
and observe the vehicle regulations in the instruction manual... your KENWOOD dealer.... that to Part 15 of ...
Operation Manual - Page 7
... claim with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual 1
1 Carefully unpack the transceiver. UNPACKING AND CHECKING EQUIPMENT
Note: The following ... bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • Hex-headed screw with the carrier immediately. If any items are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the...
Operation Manual - Page 14
If the Network Access Code matches and the squelch type is set to Selective call only if the received signal matches your transceiver, and the Network Access Code also matches, you can hear ...Individual Calls (P25) If a key has been programmed with a group ID that matches the ID set the selected Talkgroup. 4 Press and hold the microphone PTT switch to "SIGNALING" on the selected channel...
Operation Manual - Page 20
...call .
• If Manual Dialing is enabled, you ...are reserved for special messages). Messages can contain up to call by JVC KENWOOD Corporation. A maximum of 15 received messages (combined status messages and short...the microphone PTT switch and speaking into the microphone.
■ Identification Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number.
...
Operation Manual - Page 21
... > Status/Short Message > Channel > Time Stamp
3 Press to return to transmit. • If Manual Dialing is enabled, you can enter a status ID by your dealer, GPS data may be automatically transmitted...any key to return to normal operation.
■ Reviewing Messages in the same stack memory. If set up by using the microphone keypad.
6 Press the microphone PTT switch or to initiate the call....
Kenwood TK-5820 Reviews
Do you have an experience with the Kenwood TK-5820 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!