Kenwood TK-5720 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-5720 manuals!
Problems with Kenwood TK-5720?
Ask a Question
Free Kenwood TK-5720 manuals!
Problems with Kenwood TK-5720?
Ask a Question
Popular Kenwood TK-5720 Manual Pages
User Manual - Page 2
...Ground MIC Ground
Specification
I
-
-
- O
I /O
CMOS
O
13.6 V
O
Ground
- High Impedance/ CMOS
I/O
Ground
-
600 Њ
I
High Impedance
I
High Impedance
I/O
Notes
Specification RS-232C ... (D-SUB 25 Pin Connector)
Pin NO.
ENGLISH
VHF P25 TRANSCEIVER/ UHF P25 TRANSCEIVER
TK-5720/ TK-5820
Instruction Manual
Terminal Description
Microphone Jack
Pin NO. Pin Name 2 RXD1...
User Manual - Page 3
... your transceiver is mounted in this Communications Equipment. This instruction manual covers only the basic operations of dynamite blasting caps may have been added to your transceiver while taking on any customized features that the operator is licensed solely for firmware embedded in Kenwood product memories are being placed into or removed from attempting...
User Manual - Page 4
... guarantee that to Part 15 of the FCC Rules. This equipment generates, uses and can be applicable:
FCC WARNING This equipment generates or uses radio frequency energy. Please check
and observe the vehicle regulations in your Kenwood dealer. • Use of the transceiver while you are expressly approved in the instruction manual.
INFORMATION TO...
User Manual - Page 6
... for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed in the following unpacking instructions are missing or have been damaged during shipment, file a claim with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual 1
UNPACKING AND CHECKING EQUIPMENT...
User Manual - Page 7
...Be sure to drill the firewall, then install a rubber grommet.
2 Run the two power cable leads through . If your Kenwood dealer, an authorized Kenwood service facility, or the factory.
Check the battery...the self-tapping screws used to damage vehicle wiring or parts. The following preparation instructions are required for installing the transceiver: • 1/4 inch (6 mm) or larger electric drill...
User Manual - Page 13
...Calls (P25) If a key has been programmed with a group ID that matches the ID set to code your transceiver to Selective call , a ringing tone will prevent you from your transceiver settings. To ...8226; Speak into the microphone as you would during a normal transmission.
Refer to make calls to specific persons. 1 Press the key programmed as Individual.
2 Press / to select a unit ID/...
User Manual - Page 19
You can respond to the call by Kenwood Corporation. Messages can send and receive 2-digit Status messages which may be stored in your transceiver... by pressing the microphone PTT switch and speaking into the microphone.
■ Identification Codes An ID code is enabled, you want to call.
• If Manual Dialing is a combination of a 3-digit Fleet number and a 4-digit ID number.
User Manual - Page 20
...Short Message
• Press and hold for details.
To confirm the deletion, press or . or #. If set up by using the microphone keypad.
6 Press the microphone PTT switch or to initiate the call. • ... will flash and a calling ID or text message will appear when a Status call . • If Manual Dialing is enabled, you can enter a station ID by using the microphone keypad.
4 Press to enter...
User Manual - Page 22
... this key before Emergency mode was entered. NAC is a feature of P25 transceivers that was in Emergency mode. ◆ Your dealer can set the transceiver to QT/DQT;
Signaling
■ Quiet Talk (QT)/ ...begin transmitting based on your transceiver channels. A QT tone/ DQT code is set up to 40 tones/codes. 4 Press to save your new setting. 5 When you to ignore (not hear) calls from other...
Operation Manual - Page 3
... Serial Data Input Ground Ground MIC Ground
Specification
I
-
Pin Name 2 RXD1 3 TXD1
Description Serial Data Input Serial Data Output
5 DI
Data Input
6 MI2 7 GND 9 TXD2 10 RXD2 11 GND 18 GND 25 ME
Antenna Connector Impedance is 50 Њ. O
I
-
-
-
VHF P25 TRANSCEIVER
TK-5720
UHF P25 TRANSCEIVER
TK-5820
INSTRUCTION MANUAL
Terminal Description
Microphone Jack
Pin NO.
Pin...
Operation Manual - Page 4
...service to explode. The user of dynamite blasting caps may have been posted.
U.S.
Do not carry spare fuel containers in the trunk of your vehicle if your NEXEDGE mobile radio. This voice coding...KENWOOD Corporation. Firmware Copyrights The title to extract, remove, decompile, reverse engineer, or disassemble the Object Code... instruction manual covers only the basic...
Operation Manual - Page 5
...particular installation. Check the battery polarity and voltage of the vehicle before installing the transceiver.
◆ Use only a KENWOOD optional...install the transceiver securely using an optional mounting bracket and screw set so the transceiver will not occur in a residential installation...if not installed and used in the instruction manual. The user could lose the authority to Part 15 of ...
Operation Manual - Page 7
Carefully unpack the transceiver. If any items are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory.
SUPPLIED ACCESSORIES
Microphone (with cable 1 Microphone hanger (with 4 x 16 mm self-tapping screws 1 DC power cable 1 • Fuse (15 A 2 Mounting bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • Hex-headed screw...
Operation Manual - Page 14
... on the selected channel, you would during a normal transmission.
8 This will also appear on page 17 for P25 operation already have a Talkgroup ID assigned. Note: Signaling allows your transceiver to code your transceiver settings. Refer to "SIGNALING" on the display. • For best sound quality, hold the microphone approximately 1.5 inches (3 ~ 4 cm) from listening...
Operation Manual - Page 21
... the deletion, press
• To delete all messages, press and hold deletion, press or . If set up by using the microphone keypad.
6 Press the microphone PTT switch or to initiate the call. &#...Press to enter Status mode.
5 Press / to select the status you want to transmit. • If Manual Dialing is enabled, you can enter a status ID by your dealer, GPS data may be automatically transmitted ...
Kenwood TK-5720 Reviews
We have not received any reviews for Kenwood yet.