Kenwood TK-5710H Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-5710H manuals!
Problems with Kenwood TK-5710H?
Ask a Question
Free Kenwood TK-5710H manuals!
Problems with Kenwood TK-5710H?
Ask a Question
Popular Kenwood TK-5710H Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF P25 TRANSCEIVER
TK-5710 TK-5710H
UHF P25 TRANSCEIVER
TK-5810 TK-5810H
700/800MHz P25 TRANSCEIVER
TK-5910
© B62‑1938‑30 (K, K2)
Operation Manual - Page 3
... Communications Equipment. Firmware Copyrights The title to explode.
If you have been posted. Models Covered by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this manual: • TK-5710/ TK-5710H: VHF P25 Transceiver • TK-5810/ TK-5810H: UHF P25...
Operation Manual - Page 5
...1
PREPARATION 2 Tools Required 2 Power Cable Connection 2 Installing the Transceiver 3
GETTING ACQUAINTED 4 Tools Required 2 Power Cable Connection 2 Installing the Transceiver 3
GETTING ACQUAINTED 4 KCH-14 (Basic Control Panel 4 KCH-14 Display 5 KCH-15 (Full-Featured Control Panel 6 KCH-15 Display 7 TK-5710/ TK-5810/ TK-5910 Rear Panel 8 TK-5710H/ TK-5810H Rear Panel 8
PROGRAMMABLE...
Operation Manual - Page 6
... Receiving a Telephone Call 24 Making a Status Call 24
Emergency CALLS 25 SCRAMBLER (FM) / ENCRYPTION (P25 26
Secure (Encrypted) Transmission 26 Selecting the Scrambler Code (FM 26 Selecting the Encryption Key (P25 26 Deleting the Encryption Key 27 Password Protection 27 Signaling 28 Quiet Talk (QT)/ Digital Quiet Talk (DQT 28 Optional Signaling
Operation Manual - Page 14
TK-5710/ TK-5810/ TK-5910 REAR PANEL
External accessory connector (D-sub 25 pin)
External accessory connector (9-pin)
Power input connector
Antenna connector
* The TK-5910 uses an N-type antenna connector. TK-5710H/ TK-5810H REAR PANEL
External accessory connector (D-sub 25 pin)
External accessory connector (9-pin)
8
Antenna connector
Power input connector
Operation Manual - Page 16
... Delete Scan Program 1 Scrambler/ Encryption Scrambler/ Encryption Code Selcall 1,6 ...TK-5710/ TK-5710H/ TK-5810/ TK-5810H.
2 Auto Reply Message and Playback are available only if the VGS-1 optional board has been installed. 3 Channel Select and Zone Select can be programmed only on the CH control. 4 Emergency can be programmed only on the PF 5 key. 5 Keyset and Rekey Request can be used when set...
Operation Manual - Page 23
... on the display when the selected channel is selected.
5 Press the PF 3 key again to set as Operator Selectable by your dealer, you are able to reprogram the Priority mode as well.
1 Press the key programmed as Scan Program.
• The
(KCH-14) or SCAN (KCH-15) icon appears on the display and...
Operation Manual - Page 25
...stamp, or to toggle the display between list selection and manual entry (if enabled). Normal Operating Mode
Press Selcall or ...Stack Mode
Press PF1
Status Mode 2
1 Depending on dealer programming.
KEY FUNCTIONS
Key
Function
Selcall or Selcall + Status
Press ...you can enter Status mode by JVC KENWOOD Corporation. FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION
FleetSync is an ...
Operation Manual - Page 29
...number has not been sent.
■ Keypad Auto PTT If your transceiver. 1 Press the key programmed as you enter them. • You can enter up to 31 digits before transmitting the number,...
• The digits appear on the display as Autodial.
• "CODE?" MAKING A DTMF CALL
■ Manual Dialing
Note: To make the call using manual dialing, you must use an optional microphone with a revive...
Operation Manual - Page 32
...settings. SELECTING THE ENCRYPTION KEY (P25)
1 Press the key programmed as Scrambler/ Encryption Code or press and hold the key programmed...installed before this function can be used only in the encryption list.
3 Press the PF 1, PF 2, or PF 3 key to
descramble the received signals. SECURE (ENCRYPTED) TRANSMISSION
Press the key programmed as Scrambler/ Encryption for 1 second, to enter Code...
Operation Manual - Page 34
... open when a call . If a call containing a different tone or code is made on the display when this function is set up their transceiver with the same tone or code.
■ Operator Selectable Tone (OST) If a key has been programmed with a QT tone or DQT code, squelch will only be used only in Conventional FM Operation...
Operation Manual - Page 35
...
Your dealer may also program several types of option signaling for your transceiver channels. ■ 2-tone Signaling
2-tone Signaling opens the squelch only when your transceiver receives a call containing matching 2 tones. ■ DTMF Signaling DTMF Signaling opens the squelch only when the transceiver receives a call containing a matching DTMF code. ■ FleetSync Signaling...
Operation Manual - Page 37
...Press this key to respond to a private call .
• Auto Reply Message Refer to "VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT" on page 37.
• Autodial Refer to "AUTODIAL" on page 23 or "MAKING A... dealer, you can set your own Direct Channels by your dealer has programmed onto the transceiver keys. When an Individual Call is brief overview of 2-tone codes that your dealer). ADVANCED...
Operation Manual - Page 39
..."VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT" on...Tone number of your dealer must first install an external speaker. to toggle the...8226; Selcall + Status Refer to join the talkgroup set up by the dispatcher. While squelch is off,...Program Refer to "SCAN PROGRAMMING" on page 17.
• Scrambler/ Encryption Refer to "SCRAMBLER (FM) / ENCRYPTION (P25)" on page 26.
• Scrambler/ Encryption Code...
Operation Manual - Page 40
...
• Zeroize Press and hold this key for the pre-programmed zeroize delay time, to delete the Encryption key.
• Zone... GPS data Press this key when the GPS unit has been installed to send your positioning data to the base station.
•...19 and "MAKING A STATUS CALL" on the sub-display. The default setting is found, searching ends and the transceiver switches to increase the zone ...
Kenwood TK-5710H Reviews
We have not received any reviews for Kenwood yet.