Kenwood TK-3406 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-3406 manuals!
Problems with Kenwood TK-3406?
Ask a Question
Free Kenwood TK-3406 manuals!
Problems with Kenwood TK-3406?
Ask a Question
Popular Kenwood TK-3406 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF FM TRANSCEIVER
TK-2406
UHF FM TRANSCEIVER
TK-3406
© B62-2481-10 (M)
Operation Manual - Page 2
...Do not touch these locations when replacing the battery pack. • Do not immerse the transceiver in KENWOOD product memories are wet. •...installing optional accessories. • The charger is punishable by KENWOOD. • If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts. • If a headset or headphone is aware of copyrights for firmware...
Operation Manual - Page 3
...your ear. Transmitting at gasoline service stations. • Near explosives or blasting sites. • In aircrafts. (Any use of the transceiver must follow the instructions
and regulations provided by the ...a time may be ejected and strike the driver or passengers. • Do not transmit while touching the antenna terminal or if any metallic parts are posted regarding the use only a speaker...
Operation Manual - Page 6
... the battery pack emits a bad odor, appears to have different coloring, is leaking (or the battery emits a bad odor), immediately remove it may cause eye-problems.
• Do not charge the battery for any other reason, remove it from the battery gets into flame.
• Do not use it .
The battery...
Operation Manual - Page 7
... (KNB-53N 1 • Speaker/ microphone jack cover 1 • Speaker/ microphone locking bracket 1 • Belt clip (KBH-10 1 • Screw (M3 x 8 mm 2 • Channel stopper 1 • Instruction manual 1 Note: Refer to "PREPARATION" for accessory installation instructions.
If any of the items listed below are missing or damaged, file a claim with the carrier immediately.
Operation Manual - Page 8
... clockwise until secure. Using the antenna in these ways may be unable to be changed.
2 Insert the channel stopper.
3 Set the arrow of the transceiver by holding the antenna at channel 1, the Channel selector knob may not install correctly and the channel may damage the antenna and degrade your transceiver's performance.
PREPARATION...
Operation Manual - Page 9
...clip using the two supplied M3 x 8 mm screws. Do not use glue which is not installed, its mounting location may crack the transceiver's back panel.
Belt clip
Note: If the ...Acrylic ester, which is designed to prevent screw loosening when installing the belt clip, as it may cause damage to remove the casing from the transceiver. Installing/ Removing the Battery Pack
◆ Do not short ...
Operation Manual - Page 12
INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET)
Note: The transceiver is not fully water resistant when using a speaker/ microphone or headset.
1 Insert the speaker/ microphone (or ...
Operation Manual - Page 14
... the microphone to transmit.
■ Emergency Press and hold down this key to transmit a 2-tone code.
■ Autodial DTMF Autodial allows you to make a private call to another party.
■ ... tone allows you to alert party members that you are making a call . Ask your dealer setting. Without Status Memory, when the transceiver power is dependent on your dealer for details on which ...
Operation Manual - Page 15
... OFF and then ON again, the keys remains locked.
■ Lone Worker Lone Worker Mode is "Operator Selectable", press this key in normal mode to set the current channel as the priority channel.
■ Scan Press this key to start scanning the transceiver channels.
On high transmit power channels, press this...
Operation Manual - Page 16
Contact KENWOOD dealer for further information.
■ Send the GPS data Press this key when the GPS unit has been installed to send your positioning data to the base station.
■ Speaker Switch Use this key to communicate directly with other party listening in on your ...
Operation Manual - Page 17
... the speaker.
4 To make a call (FleetSync signaling, etc.)
Blinks red/orange
The selected channel has not been programmed and cannot be used.
* Your dealer can set the LED to blink either orange or blue for FleetSync, DTMF, or 2-tone operation.
11
LED Indicator Status
Indicator Color Lights red Lights green Blinks...
Operation Manual - Page 18
...transceiver while the VOX function is switched ON and the VOX Gain level is performed for specific channels by selecting a channel with the Channel selector). To activate VOX and set the VOX Gain level, perform the following steps: 1 Connect the headset to the ...the Side 2 key to
activate VOX. VOICE OPERATED TRANSMISSION (VOX)
VOX operation allows you are using a supported headset.
Operation Manual - Page 19
...tone every 30 seconds and the LED indicator blinks red when the battery needs recharged or replaced.
Battery Saver
When activated by your dealer, the Battery Saver function decreases the amount of ... may flash green when receiving a QT/DQT signal which does not match the QT/DQT tone/code set up in use.
BACKGROUND OPERATIONS
Time-Out Timer (TOT)
The Time-out Timer prevents callers from...
Operation Manual - Page 20
... can be cancelled with a stun reset code. Stun can transmit a stun code to that transceiver to disable transmission or transmission/reception.
Beginning/ End of Transmission Signal
The Beginning/ End of Transmission identification signals are available with ID, and "Wild Card" Group Calling.
■ FleetSync Utilizing JVC KENWOOD's FleetSync digital signaling protocol, this transceiver...
Kenwood TK-3406 Reviews
We have not received any reviews for Kenwood yet.