Kenwood TK-2317 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-2317 manuals!
Problems with Kenwood TK-2317?
Ask a Question
Free Kenwood TK-2317 manuals!
Problems with Kenwood TK-2317?
Ask a Question
Kenwood TK-2317 Videos
[Thegioibodam.vn] So sánh 2 máy b? ?àm c?m tay Kenwood TK-2317 và Kenwood NX-240
Duration: 3:50
Total Views: 234
Duration: 3:50
Total Views: 234
????? Kenwood TK 2317 ? Motorola GP340
Duration: 2:21
Total Views: 8
Duration: 2:21
Total Views: 8
Máy b? ?àm kenwood TK 2317 - B? ?àm Kenwood chính hãng
Duration: 4:53
Total Views: 263
Duration: 4:53
Total Views: 263
[Thegioibodam.vn] So sánh 2 máy b? ?àm c?m tay Kenwood TK 2000 và Kenwood TK 2317
Duration: 3:48
Total Views: 227
Duration: 3:48
Total Views: 227
Popular Kenwood TK-2317 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF FM TRANSCEIVER
TK-2317
UHF FM TRANSCEIVER
TK-3317
© B62-2237-10 (M) 09 08 07 06 05 04 03 02 01
Operation Manual - Page 3
... transmitters within the territories under government control.
◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to and ownership of copyrights for firmware embedded in KENWOOD product memories are grateful you have chosen KENWOOD for JVC KENWOOD Corporation.
i NOTICES TO THE USER
◆ Government law prohibits the operation of any transceiver...
Operation Manual - Page 5
.... iii Transmitting at gasoline service stations. • Near explosives or blasting sites. • In aircrafts. (Any use of the transceiver must follow the instructions
and regulations provided by the... metallic parts are exposed from the transceiver, and contact your KENWOOD dealer. • Use of the transceiver while you use of explosion if the battery is incorrectly replaced; When...
Operation Manual - Page 11
...
• Speaker/ microphone jack cover 1 • Speaker/ microphone locking bracket 1 • Belt clip (KBH-10 1 • Screw set
M2.6 x 7 mm (black 1 M3 x 8 mm 2 • Instruction manual 1 Note: Refer to "PREPARATION" {page 2} for accessory installation instructions.
1
If any of the items listed below are missing or damaged, file a claim with the carrier immediately. UNPACKING AND...
Operation Manual - Page 16
... to Talk) switch Press and hold, then speak into the microphone to the table on page 7 for the LED indicator status. Rotate to change the operating zone or channel. The default setting is [Lamp].
6 Side 1 key Press to activate its programmable function. Antenna
ORIENTATION
Speaker
Battery pack
Microphone
Selector Rotate to adjust...
Operation Manual - Page 17
... their programmable functions. LED Indicator Status
Indicator Color Lights red Lights green Blinks red
Meaning Transmitting Receiving a call Battery power is [None] (no function).
A key: The default setting is low while transmitting
Blinks orange/ blue*
Receiving an encoded call (FleetSync, DTMF signaling, etc.)
* Your dealer can set the led to activate their programmable...
Operation Manual - Page 22
... you hear a caller's voice, readjust the volume as [Zone Up]/ [Zone Down]. • The default setting for the Selector is [Zone Up/ Down]. Names can turn the Scan function on if desired.
2 When ...Channel Up]. Press the key programmed as [Channel Up]/ [Channel Down]. • The default setting for channels, with up to receive.
Select the desired channel using the Selector or the keys ...
Operation Manual - Page 23
...8226; The indicator appears when the selected channel is the Priority
channel (depending on dealer setting).
To start/stop scanning, press the key programmed as [Scan Delete/Add] while ...Scan settings return to the scanning sequence. While scanning, the transceiver checks for signals on the transceiver channels. TEMPORARY CHANNEL LOCKOUT
During scan, you can temporarily remove specific ...
Operation Manual - Page 27
... the PTT switch and speak into the microphone.
■ Identification Codes An ID code is a protocol owned by your dealer, your conversation. •...zone and channel. 2 Press the key programmed as [Selcall] or [Selcall + Status] to enter Selcall mode. • The last selected station ID appears on the...set up by JVC KENWOOD Corporation. Each transceiver must have its own Fleet and ID number.
Operation Manual - Page 30
... can be adjusted from levels 1 (low sensitivity) to 10 (high sensitivity), and off. The default setting is noise in the background. VOX OPERATION
1 Press and hold the key programmed as [VOX] when ...8226; The current VOX Gain level appears on the VOX Gain level.
4 When you to save the setting.
20
If it will occur when there is level 5.
3 While adjusting the level, speak into the...
Operation Manual - Page 32
...of a repeater, as long they are not too far away or there are no geographical obstacles in service (such as a power failure), you can make emergency calls. 1 Press and hold the key programmed as... [Emergency].
• Depending on how the transceiver is set up.
2 To exit Emergency mode, press and hold the [Emergency] key again. • If the ...
Operation Manual - Page 33
... OFF. • The indicator appears while the Scrambler is activated. Contact your KENWOOD dealer for
1 second. • The indicator and current scrambler code appear. 2 Press to select your desired scrambler code. 3 Press S to store the new setting. • After changing your transceiver scrambler code: 1 Press and hold the key programmed as [Scrambler] for further information...
Operation Manual - Page 34
... operation.
• Monitor Momentary: Press and hold to hear background noise. Release to return to normal operation.
• Squelch Off: Press to store the new setting. and the current squelch level appear. 2 Press to select the desired squelch level from
0 (open) to 9 (tight). 3 Press S to hear background noise.
MONITOR/ SQUELCH OFF...
Operation Manual - Page 35
... operations are being performed for 5 seconds.
Note: While the Battery Saver is very low, replace or recharge the battery pack. High
Sufficient
Low
Very Low (flashing)
When the battery power is...may flash green when receiving a QT/DQT signal which does not match the transceiver QT/DQT setting. Release the PTT switch. When a signal is received or an operation is low while transmitting....
Operation Manual - Page 36
... or wait until the channel becomes free. PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is already in use. BUSY CHANNEL LOCKOUT (BCL)
If BCL is set up by your dealer, you will remove excessive noise from transmitted signals, to transmit if...
Kenwood TK-2317 Reviews
We have not received any reviews for Kenwood yet.