Kenwood NX-740HV Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-740HV manuals!
Problems with Kenwood NX-740HV?
Ask a Question
Free Kenwood NX-740HV manuals!
Problems with Kenwood NX-740HV?
Ask a Question
Popular Kenwood NX-740HV Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF DIGITAL TRANSCEIVER
NX-740H NX-740HV
UHF DIGITAL TRANSCEIVER
NX-840H NX-840HU
B5A-0031-20 (K)
Operation Manual - Page 3
This instruction manual covers only the basic operations of unlicensed transmitters within the territories under government control.
◆ Illegal operation is punishable by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. Ask your radio.
The AMBE+2TM voice coding Technology embodied in KENWOOD product memories are ...
Operation Manual - Page 4
... securely using the supplied mounting bracket and screw set so the transceiver will not break loose in 12 V negative ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver.
◆ Use only the supplied DC power cable or a KENWOOD optional DC power cable. ◆ Do not cut...
Operation Manual - Page 5
... cable) • KMC-30 (NX-740H/ NX-840H 1 • KMC-35 (NX-740HV/ NX-840HU 1 Microphone hanger (with the carrier immediately. If any items are not properly protected from the radio frequency energy which is present while transmitting. GETTING STARTED
Note: The following instructions are for use a circle cutter to drill a hole, then install a rubber grommet.
2 Run...
Operation Manual - Page 6
..., install the transceiver securely using the supplied mounting bracket and screw set, ... careful not to damage vehicle wiring or parts.
1 Mark the position of a collision.
Note: Before installing the transceiver, check how far the mounting...Fuse
12 V vehicle battery
2 When replacing the fuse in a place where they
will extend below the surface. Never replace a fuse with one that is suf&#...
Operation Manual - Page 8
Appears when switch the transceiver ON.
6
The Transceiver Password function is programmed. (PS)
Appears during Scan. (Sc)
8
The selected channel is the Priority channel. (P)
9
Appears when a channel is added to the scan list. (cA)
9
...
Operation Manual - Page 9
...Sr)
12
Appears when the Encryption function is on. (Ec)
12
Appears when the Scrambler/ Encryption code mode is on. (co)
12
Appears when the Squelch Level setting is on. (SL)
13
Appears when the Public Address function is on. (PA)
13
Appears... as listed below.
• Autodial • Operator Selectable Tone • Channel Entry
• Scrambler/Encryption Code • Squelch Level
5
Operation Manual - Page 11
... ON. • A beep sounds and the display illuminates. • If the Transceiver Password function is programmed, "PS" will prevent you from your desired zone and channel. 2 ... "16" (Channel 16) appears on the display.
Note: Signaling allows your transceiver to code your transceiver settings. ADJUSTING THE VOLUME
Press the [Volume Up] key to background noise while adjusting the volume...
Operation Manual - Page 12
...target transceiver instead of initiating a voice call . • Your dealer may also have been set up with an individual or group ID list number.
The transceiver will sound. SCAN
Scan ... start / stop scanning, press the key programmed as [Call 1] or [Call 2], if they have set up with an NXDN Status. • Select the desired channel before you receive an individual call ....
Operation Manual - Page 13
...• If there is no data in the redial memory, an error tone will automatically change to the Priority channel when a call is ...on a normal channel. • "P" appears on the display.
MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the ...restarted, the
Scan settings return to remove a channel.
• When a channel is removed, "cd" appears on dealer setting). you must use ...
Operation Manual - Page 14
When a channel is set up with a revive code. • "St" appears on the display while the transceiver is stunned....Wild Card" Group Calling.
2-TONE
2-tone Signaling opens the squelch only when your transceiver receives a call containing a stun code, the transceiver becomes disabled.
RADIO ACCESS NUMBER (RAN)
RAN is included for digital radio communications. When the transceiver receives a...
Operation Manual - Page 15
...will blink when a Selcall has been received. Note: If set up by your dealer, your transceiver may be limited by ...PAGING FUNCTION
FleetSync is an Alphanumeric 2-way Paging Function and is installed on the display, followed by your dealer. 1 Select your ...switch and speak into the microphone.
■ Identification Codes An ID code is a voice call to a particular station or to transmit ...
Operation Manual - Page 16
...not operated for 1 second. TALK AROUND
During interruptions in service (such as a power failure), you can continue to ...enters Emergency mode, the transceiver will change the scrambler/ encryption codes:
12 When activated, any other transceivers without the use ... this key to normal.
■ Lone Worker Mode Lone Worker Mode is set up.
2 To exit Emergency mode, press and hold the [Emergency] key...
Operation Manual - Page 17
...]. • "SL" appears on the display, followed by the current scrambler/ encryption code.
2 Press to select your desired scrambler/ encryption code. 3 Press S or to store the new setting.
• After changing your scrambler/ encryption code, be used with different scrambler/ encryption codes.
MONITOR/ SQUELCH OFF
You can use the key programmed as [Monitor] or [Squelch...
Operation Manual - Page 18
... transceiver as [LED Brightness].
VOICE ANNOUNCEMENT
When changing the zone/ channel, an audio voice will sound.
PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is used with optional boards. • "AU" appears on how BCL functions when using a channel for a preset...
Kenwood NX-740HV Reviews
We have not received any reviews for Kenwood yet.