Kenwood NX-740 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-740 manuals!
Problems with Kenwood NX-740?
Ask a Question
Free Kenwood NX-740 manuals!
Problems with Kenwood NX-740?
Ask a Question
Popular Kenwood NX-740 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF DIGITAL TRANSCEIVER
NX-740
UHF DIGITAL TRANSCEIVER
NX-840
© B5A-0032-10 (C)
Operation Manual - Page 3
...metal box with a padded interior.
i This instruction manual covers only the basic operations of dynamite blasting caps may have added to your radio.
Do not carry spare fuel containers in the ... chosen KENWOOD for information on any transceiver.
◆ EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations....
Operation Manual - Page 4
... contact your area. • Do not use options not specified by KENWOOD.
◆ The transceiver operates in 12 V negative ground systems only!
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in the event of the vehicle before...
Operation Manual - Page 5
...
Carefully unpack the transceiver. DC power cable (with fuses 1 • 10 A fuse 4 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • M4 x 8 mm Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual 1
PREPARATION
Various electronic equipment in 12 V negative ground systems only! If your vehicle contains such...
Operation Manual - Page 6
... Transceiver
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will extend below the surface. Never replace a fuse with one that is suf&#...Mounting bracket
Fuse
12 V vehicle battery
2 When replacing the fuse in the DC power cable, be careful not to damage vehicle wiring or parts.
1 Mark the position of the holes in ...
Operation Manual - Page 8
DISPLAY
The display shows the zone/ channel number and the 2 dots show various modes of operation.
Appears when switch the transceiver ON.
The Transceiver Password function is programmed. (PS)
6
Appears during Scan. (Sc)
8
The selected channel is the Priority channel. (P)
9
Appears when a channel is added to the scan list. (cA)
9
...
Operation Manual - Page 9
...Sr)
12
Appears when the Encryption function is on. (Ec)
12
Appears when the Scrambler/ Encryption code mode is on. (co)
12
Appears when the Squelch Level setting is on. (SL)
13
Appears when the Public Address function is on. (PA)
13
Appears... as listed below.
• Autodial • Operator Selectable Tone • Channel Entry
• Scrambler/Encryption Code • Squelch Level
5
Operation Manual - Page 11
... code your desired zone and channel. 2 Press the key programmed as [Zone Up]/ [Zone Down] and [Channel Up]/ [Channel Down]. • "G1" (Zone 1)/ "16" (Channel 16) appears on the display. If Squelch Off has been programmed onto a key, you enter an incorrect password... to transmit. Refer to "SIGNALING" on the selected channel, you will prevent you from your transceiver settings.
Operation Manual - Page 12
... to the call by pressing the key programmed as [Call 1] or [Call 2], if they have set up with an individual or group ID list number.
To make an Individual or Group call when pressing...initiating a voice call will sound. To start the call. • Your dealer may also have been set Selcall on PTT for Individual or Group calls, allowing you respond to the scanning sequence.
8 NXDN
NXDN...
Operation Manual - Page 13
...; The channel is no data in the redial memory, an error tone will automatically change to the Priority channel when a call...Note: Switching the transceiver power OFF clears the redial memory.
9 MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the desired...need to press the PTT switch to scan, "cA" appears on dealer setting). REDIALING
1 Press the key programmed as [Autodial] or the key. ...
Operation Manual - Page 14
... ID Encode, Emergency Encode, Stun/ Revive Decode, and Radio Check Decode.
NXDN ID
NXDN ID is included for digital radio communications.
RADIO ACCESS NUMBER (RAN)
RAN is made on the display ...transceiver cannot decode MDC-1200 if the FleetSync baud rate is received.
When a channel is set up with a revive code. • "St" appears on the channel you are available with ID, and "...
Operation Manual - Page 15
...Selcall has been received. Note: If set up by programming.
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION
FleetSync is an Alphanumeric 2-way Paging Function and is installed on the display, followed by the current... your PTT ID list and begin your conversation.
■ Receiving If enabled by JVC KENWOOD Corporation. press the PTT switch to transmit and release it to receive. 5 To exit...
Operation Manual - Page 16
... obstacles in complete privacy. TALK AROUND
During interruptions in service (such as a power failure), you must hold the... mode, the transceiver will change the scrambler/ encryption codes:
12
ADVANCED OPERATIONS
EMERGENCY CALLS
If your transceiver has...a tone and automatically enter Emergency operation.
If the transceiver is set up.
3 To exit Emergency mode, press and hold a conversation...
Operation Manual - Page 17
... as [Squelch Level]. • "SL" appears on the display, followed by the current scrambler/ encryption code.
2 Press to select your desired scrambler/ encryption code. 3 Press S or to store the new setting.
• After changing your scrambler/ encryption code, be sure to inform all of your group members of 4 functions: • Monitor: Press to deactivate...
Operation Manual - Page 18
... used with optional boards. • "AU" appears on how BCL functions when using a channel for 1 second. PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is already in analog operation. BUSY CHANNEL LOCKOUT (BCL)
When activated, BCL prevents you would during a normal...
Kenwood NX-740 Reviews
We have not received any reviews for Kenwood yet.