Kenwood NX-740.NX-840 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood NX-740.NX-840 manuals!
Problems with Kenwood NX-740.NX-840?
Ask a Question
Free Kenwood NX-740.NX-840 manuals!
Problems with Kenwood NX-740.NX-840?
Ask a Question
Popular Kenwood NX-740.NX-840 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF DIGITAL TRANSCEIVER
NX-740
UHF DIGITAL TRANSCEIVER
NX-840
© B5A-0030-10 (M)
Operation Manual - Page 3
This instruction manual covers...that the operator is punishable by fine and/or imprisonment. ◆ Refer service to the operation of , and understands, hazards common to qualified technicians only... they are being placed into or removed from the container. If you have chosen KENWOOD for information on any transceiver.
◆ EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, ...
Operation Manual - Page 4
....
◆ Use only the supplied DC power cable or a KENWOOD optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable.
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in 12...
Operation Manual - Page 5
... cutter to drill a hole, then install a rubber grommet.
2 Run the power cable through . • If no hole exists, use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Typical examples include electronic fuel injection, anti-skid braking, and cruise control.
GETTING STARTED
Note: The following instructions are missing or have been damaged...
Operation Manual - Page 6
... in the DC power cable, be careful not to replace it will be within easy reach of the user and where there is rated with a higher value. ■ Installing the Transceiver
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not interfere with the...
Operation Manual - Page 8
... transceiver ON. Display
Description
Page
Zone Display (Zone 1)
7
Zone Display (Zone 2)
7
Channel Display (Channel 16)
7
Appears during the transceiver is stunned. (St)
10
4
The Transceiver Password function is programmed. (PS)
6
7
Appears during Scan, Voting and Voting with Signaling. (Sc)
8
The selected channel is the Priority channel. (P)
9
Appears when a channel is added...
Operation Manual - Page 9
...Sr)
12
Appears when the Encryption function is on. (Ec)
12
Appears when the Scrambler/ Encryption code mode is on. (co)
12
Appears when the Squelch Level setting is on. (SL)
13
Appears when the Public Address function is on. (PA)
13
Appears... as listed below.
• Autodial • Operator Selectable Tone • Channel Entry
• Scrambler/Encryption Code • Squelch Level
5
Operation Manual - Page 11
... while adjusting the volume level. Note: Signaling allows your transceiver to code your transceiver settings.
If signaling has been programmed on the display. SELECTING A ZONE AND CHANNEL
Select the desired zone and channel using an optional microphone with a keypad, simply enter the password digits and proceed to step 3. 2 Press C> to accept the entered...
Operation Manual - Page 12
... reset timer expires before sending the status call . • Your dealer may also have been set the duration for the auto reset timer (default is 10 seconds). Note: To use Scan, there...
to start / stop scanning, press the key programmed as [Call 1] or [Call 2], if they have set up on the transceiver channels. The transceiver will remain on the display during Scan. • When a signal...
Operation Manual - Page 13
.... However, when scanning is removed, "cd" appears on dealer setting).
SCAN DELETE/ ADD
You can temporarily remove specific channels ... The channel is no data in the redial memory, an error tone will automatically change to the Priority channel when a call... to quickly call DTMF numbers that channel, even if call .
MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the ...
Operation Manual - Page 14
... only hear calls from other parties who are using , you are available with a RAN, squelch will not hear the call containing a stun code, the transceiver becomes disabled. When a channel is set up with the built-in MDC signaling: PTT ID Encode, Emergency Encode, Stun/ Revive Decode, and Radio Check Decode. Note: The...
Operation Manual - Page 15
... FleetSync. Note: If set up by your desired...9632; Identification Codes An ID code is a voice call ...installed on the display, followed by programming. PAGING CALL
1 Select your desired zone and channel. 2 Press and hold
the key. • "ot" appears on your transceiver, you can change the preset encode and decode tones for 1 second to 16 OST pairs can be pre-programmed by JVC KENWOOD...
Operation Manual - Page 16
... in complete privacy. TALK AROUND
During interruptions in service (such as [Lone Worker] to understand your conversation...)/ "Ec"(NXDN) appears on how the transceiver is set up.
2 To exit Emergency mode, press and hold... function ON or OFF. Contact your KENWOOD dealer for 1 second. If the transceiver is ... you can change the scrambler/ encryption codes:
12
Press the key programmed as...
Operation Manual - Page 17
... the current squelch level. 2 Press to select the desired squelch level from 0 to 9. 3 Press S or to store the new setting.
MONITOR/ SQUELCH OFF
You can only be used with different scrambler/ encryption codes. PUBLIC ADDRESS (PA)
The PA system can use the key programmed as [Public Address] to activate the Public Address...
Operation Manual - Page 18
... transmitting and a warning tone will remove excessive noise from using QT, DQT, RAN, or Optional signaling.
PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is used only in analog operation. COMPANDER
If programmed by pressing the key programmed as [AUX] to...
Kenwood NX-740.NX-840 Reviews
Do you have an experience with the Kenwood NX-740.NX-840 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!