JVC DT-V17G15Z Support and Manuals
Get Help and Manuals for this JVC item
View All Support Options Below
Free JVC DT-V17G15Z manuals!
Problems with JVC DT-V17G15Z?
Ask a Question
Free JVC DT-V17G15Z manuals!
Problems with JVC DT-V17G15Z?
Ask a Question
Popular JVC DT-V17G15Z Manual Pages
Instruction Manual - Page 1
which is located on the rear of the cabinet. Model No. : Serial No. :
DT-V17G15Z
LCT2698-001A MULTI FORMAT LCD MONITOR
DT-V17G15Z
INSTRUCTIONS
For Customer Use: Enter below the Serial No. Retain this information for future reference.
Instruction Manual - Page 3
...service to dangerous voltages and other equipment as the disconnect device, the disconnect device shall remain readily operable. If the product is installed in accordance with the instruction manual, may touch dangerous voltage points or short-circuit the parts... injury by accidental fall
Fix the monitor to a wall by JVC could result in a residential area is left unattended and unused ...
Instruction Manual - Page 4
... this product, please contact your local municipal
office, your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from the sources of the disturbance.
4 European representative of JVC KENWOOD Corporation is: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany
Information for Users on or...
Instruction Manual - Page 10
... signal on an SDI signal) is not displayed correctly, change the setting of "DVI INPUT SEL." (☞ page 21)
9 Screw holes... connections are complete. • Refer also to the E. Index of Parts and Functions (cont.)
Rear panel
Carry handle Use this slot. When... on the monitor after turning on or in to the user manual of each piece of equipment.
1 REMOTE terminal Terminal for the...
Instruction Manual - Page 11
... 29 and "Signal format" on page 12.
3 Source name assigned in "CHARACTER SET." (☞ "INFORMATION" on page 20)
● Displayed when "SOURCE ID" is set to "ON." (☞ "INFORMATION" on page 20) ● A red square is displayed when an error occurs.
5 Time code
● Press T.C. Use the T.C.
Showing Input Signals
Audio Channel Selection
Select...
Instruction Manual - Page 12
...change the input - When you turn on the monitor ● When "STATUS DISPLAY" is set to "OFF." On the signal format The following cases:
- Status indication of 3G SDI..."INFORMATION." (☞ page 20) ● When "STATUS DISPLAY" is set to "AUTO" or one of the manual settings(☞ "SDI FORMAT" on page 21).
4 Setting of "MUTING"
● Displayed only when muting is activated (☞ ...
Instruction Manual - Page 13
SIZE/POSI. WHITE BALANCE SET. STATUS DISPLAY TIME CODE CRC ERROR SUB HOUR METER MODEL VERSION HOUR METER
SERIAL TYPE PARALLEL TYPE PIN1 PIN2 ...SYSTEM
TALLY SELECT
CONTRAST
DIMMER
BRIGHT
COMPONENT PHASE
CHROMA
COLOR GAMUT
PHASE
LCD SAVER
NTSC SETUP
COMPO. MAIN MENU
Item being selected
Operation guide
SET-UP MENU
2 Press buttons to select an item, then press button.
● ...
Instruction Manual - Page 14
... LEVEL *1 CTI LTI I/P MODE
Simultaneously corrects the frequency characteristics of the chrominance signal. Adjust the clearness of the outlines of the RGB colors.
only)
Setting for the picture quality.
SDI DUAL LINK Setting value: OFF, ON
Activates/deactivates the DUAL LINK function of SDI signals. ● "DUAL LINK" is displayed when the...
Instruction Manual - Page 18
... lighting color of the tally lamp, the brightness of the LCD SAVER. UPPER1 : Displays the current setting and adjustment bar at the lower part of the side panel. UPPER2 : Displays the current setting at the lower part of the picture contrast. OFF, READY
START AFTER
Display required time until the LCD SAVER operation starts...
Instruction Manual - Page 19
... *1*2 G CUT OFF *1*2 B CUT OFF *1*2 sub menu reset *2
Content Select a gamma correction.
Item CONTRAST *1 BRIGHT *1 CHROMA *1 PHASE *1, *2 NTSC SETUP
COMPO. Adjust the standard level for each input. *2 When "COMPONENT PHASE" (☞ page 18) is set -up signal), SMPTE (compliant with M2VTR signals)
Display the sub menu which enables you to about 6500K inherent...
Instruction Manual - Page 20
...information display (☞ "On the Information Display" on page 11).
space
STATUS DISPLAY
TIME CODE CRC ERROR
SUB HOUR METER
MODEL VERSION HOUR METER
4 Press button to move the arrow to the next space.
●....
You can also enter a name using the RS-232C system. Item
Content
Setting value
SERIAL TYPE
PARALLEL TYPE
PIN1 PIN2 PIN3 PIN4 PIN5
PIN6 PIN7 PIN8
Select the input terminal used for...
Instruction Manual - Page 21
... off (on the front panel. ● The following operations are available. -
When you
operate the monitor with "AUTO", select the setting value according to the input signal format. ● "M"(meaning "Manual") is not displayed correctly with "AUTO." ● DVI-D input of the monitor to control the buttons on standby).
21 VOLUME adjustment...
Instruction Manual - Page 26
...battery or replace it with...problem, unplug the monitor and consult an authorized dealer or service center. Wrong color, no sure method to solve this problem...SET-UP MENU. ● Check whether the setting of 1:1 is appropriate. ● Check whether the input signal format is not a malfunction.
● Red spots, blue spots and green spots on the menu. Troubleshooting
Solutions to common problems...
Instruction Manual - Page 28
...) REMOTE (RS-232C)
☞ "Using the serial communication" on ambient conditions for installation.)
AC 120 V/AC 220 - 240 V, 50 Hz/60 Hz or DC 12 V...Specifications
General
Model name Type Screen size Aspect ratio Compliant video signal format Format
Audio output Operation environment
Power requirements Rated current
External dimensions (excluding protruding parts)
Mass Accessories
DT-V17G15Z...
Instruction Manual - Page 32
© 2012 JVC KENWOOD Corporation
LCT2698-001A
MULTI FORMAT LCD MONITOR DT-V17G15Z
JVC DT-V17G15Z Reviews
We have not received any reviews for JVC yet.