JET Tools L-100-250-10 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools L-100-250-10 manuals!
Problems with JET Tools L-100-250-10?
Ask a Question
Free JET Tools L-100-250-10 manuals!
Problems with JET Tools L-100-250-10?
Ask a Question
Popular JET Tools L-100-250-10 Manual Pages
User Manual - Page 1
M-106210 Revision C 04/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
L-100 Series Hand Chain Hoists
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... through distributors only. Parts; Light-Duty Air Tools 1 Year - Manual Hoist Accessories; Hand Tools
NOTE: JET is Covered This warranty covers any additional action needed.
Who is constantly adding new products. More Information JET is Covered This warranty covers only the initial purchaser of the product from the date of an Authorized Service Center in duration based...
User Manual - Page 3
... local supplier or JET. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This tool has been designed and constructed to provide years of Contents ...3 Introduction ...3 Warning...4 Specifications ...5 Using the Chain Hoist ...6
Prior to Load Chain Sprocket (all models)...9 Load Chain and...
User Manual - Page 4
...set " over people.
9. Do not use . Always replace the safety latch and/or the hook before attempting assembly or operation.
2.
Read and understand the entire owners manual before placing the chain hoist back into service... it may cause damage to a qualified Walter Meier repair station.
19. Always take time to study the job...purposes, JET disclaims any real or implied warranty and holds itself ...
User Manual - Page 6
...hook needs to warn of the bottom or top hook reaches 10°, replace the hook (see Figure 2).
6
Figure 1 Figure 2 For your JET chain hoist are made at the neck of an overload. If...for damage and elongation. Support for proper fit and durability. and 20-ton hoists do not have two indicator points (A, Figure 1) cast into service.
3. Check the chain for 10- The brake mechanism ...
User Manual - Page 9
...Installation on the following page, proceeding to Figure 11:
1. to 20-Ton Hoists.
9 Replace the entire chain. Remove the cotter pin (A) and the chain anchor pin (C) on page 13 for specific...
3. If the trouble persists, inspect the chain and mating parts for gouges, nicks...models)
Install the new load chain onto the load chain sprocket as follows , referring to 5-Ton hoists, or 10...
User Manual - Page 12
...replacement chain must be performed by calling your JET distributor or from your dealer or visiting our web site at waltermeier.com.
10. Check and inspect the brake system frequently.
9. After servicing... and Maintenance Instructions. Failure to qualified repair personnel.
6. Leave all ANSI and JET inspection and maintenance instructions. Contact a Walter Meier authorized service center by...
User Manual - Page 13
... when the "A" measurement is indicated. Figure 15
A B
Figure 16
Replacement Parts
Replacement parts are listed on the following pages. As illustrated in the table above.
Never extend load chain by welding.
"A" Limit
1.47" 1.44" 1.88" 1.97" 2.17" 2.60" 3.24"
---- To order parts or reach our service department, call will allow us to the original. "B" Norm
-------2.52...
User Manual - Page 18
...-100WO-14-1L .. Overload Limiter Assembly (used on overload protection model 1
(Available from 2010-02-01 1.5x15 mm 1 12 L100-100-12 Hand Chain - L100-100 Chain Hoist (1 Ton)
Parts listed under each assembly are parts that make up that assembly (sold as an assembly only).
Wheel Washer (Available from 2010-02-01 1 11 L100...
User Manual - Page 20
...10 L100-50-10 Pin...1 L100-100-10-1........... Index No. Part No. Overload Limiter Assembly (used on overload protection model 1 L100-300WO-14-1L .. Overload Limiter Assembly (used on overload protection model...Guide 2 8A L100-50-8A Warning Label 1 9 L100-50-9 Positional Collar 1 L100-100-9-1 Wheel Stopper (Available from 2010-02-01 1
20 specify length 5x25 mm 1 13 L100-100...
User Manual - Page 21
... 1
Note: When ordering replacement chain (Index #12,...-100-28 Rivet 3x6 mm 4 29 L100-150-29 Name Plate...1 29 L100-150WO-29........ Parts ...model 1 30 L100-300-30 Spur Gear Assembly 2 Spur Gear ...2 Pinion Gear...2 31 L100-300-31 Load Sheave 1 31A............L100-50-31A C-Clip 21 mm 1 31B............L100-50-31B Needle Bearing d14xD21x12 mm........... 1 32 L100-300-32 Guide...
User Manual - Page 22
... protection model 1
(Available from 2010-02-01 1.5x15 mm 1 12 L100-100-12 Hand Chain - Disc Hub (Available from 2010-02-01 M8 1 10 L100-500-10 Pin...1 L100-100-10-1........... Parts List ...Cover Assembly 1 Hand Wheel Cover 1 Hand Chain Guide 2 8A L100-50-8A Warning Label 1 9 L100-500-9 Positional Collar 1 L100-100-9-1 Wheel Stopper (Available from 2010-02-01 1
...
User Manual - Page 23
... 2010-02-01 1 L100-WT Warning Tag (not shown 1
Note: When ordering replacement chain (Index #12, #37), specify length.
23 Parts List: L100-200 Chain Hoist (2 Ton)
20 L100-200-20 Wheel Side Plate Assembly...mm 1 32 L100-200-32 Guide Roller 2 33 L100-200-33 Stripper ...1 34 L100-200-34 Chain Anchor Plate 1 35 L100-200-35 Chain Anchor Pin 1 36 L100-100-36 Split Pin 2x15 mm 1...
User Manual - Page 29
...model 1 30 L100-500-30 Spur Gear Assembly 2 Spur Gear ...2 Pinion Gear...2 31 L100-500-31 Load Sheave 1 31A............L100-500-31A C-Clip 24 mm 1 31B............L100-500-31B Needle Bearing 17x24x15 mm 1 32 L100-500-32 Guide...28 L100-100-28 Rivet ...Parts List: L100-1000 Chain Hoist (10 Ton)
15 L100-100-15 Snap Ring 10 mm 2 16 L100-100-16 Pawl...2 17 L100-100...52 Set Screw ...
User Manual - Page 35
Record your purchase and installation information here
Purchased from: Serial Number: Stock Number: Location Installed: Date Installed:
Date: Model Number:
L-100- Date in Service:
35
JET Tools L-100-250-10 Reviews
We have not received any reviews for JET Tools yet.