JET Tools ESR-1650-1T Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools ESR-1650-1T manuals!
Problems with JET Tools ESR-1650-1T?
Ask a Question
Free JET Tools ESR-1650-1T manuals!
Problems with JET Tools ESR-1650-1T?
Ask a Question
Popular JET Tools ESR-1650-1T Manual Pages
User Manual - Page 1
M-756027 Revision C 12/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
50-inch Electrical Slip Roll Machine
Model ESR-1650T-1, ESR-1650T-3
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... located throughout the United States. Parts; Shop Tools;
Please note that you specific legal rights, subject to provide proof of metal, plastics, or other natural items that are given as expendable parts or accessories expected to a Two Year Warranty. More Information JET is a division of our tools needs service or repair, please contact Technical Service by a 90 day limited...
User Manual - Page 3
2.0 Table of Contents
1.0 Warranty and Service ...2 2.0 Table of Contents ...3 3.0 Safety warnings ...4 4.0 Introduction...5 5.0 Specifications ...6 6.0 Features and Terminology ...7 7.0 Floor ... ...10 13.0 Troubleshooting the ESR-1650T Slip Roll 11 14.0 Replacement Parts ...11 14.1 Assembly Drawing for ESR-1650T 12 14.2 Parts List for ESR-1650T...13 15.1 Wiring Diagram for ESR-1650T-1 16 15...
User Manual - Page 4
...specifically designed to determine that is damaged should be properly repaired or replaced.
18. Form a habit of the machine, a guard or other reproductive harm. Check for other part that it on.
16. A guard or other purposes, JET...the floor.
14. they become obscured or removed.
4. Before operating this manual. To reduce your exposure to these chemicals, work in the OFF position ...
User Manual - Page 5
... are any sharp metal edges of trouble free operation if used in accordance with the following safety notices used in this manual. Use leather gloves when handling workpieces.
29. Turn off and do not use power tools in minor injury and/or possible machine damage. Familiarize yourself with instructions set forth in serious injury or...
User Manual - Page 6
..., changes or alterations to comply may cause serious injury!
6
5.0 Specifications
Model ESR-1650T-1 ESR-1650T-3 Stock Number 756027 756028
Construction: Frame cast iron cast iron Rolls steel, ground and polished steel, ground and polished
Capacities: Maximum Thickness - Read and understand the entire contents of this manual were current at time of publication, but because of...
User Manual - Page 8
... diagram affixed to electrical box 1 Instruction and parts manual 1 Warranty card
Remove all parts are intact. Missing parts, if any, should be reported to the floor using a plug, install a proper 460V, ULlisted plug.
8
Lifting equipment should be connected to your distributor. Remove this machine.
Single phase model: The ESR-1650T-1 is installed.
On the transformer, remove...
User Manual - Page 9
...manual... thickness. Figure 5
9 It is recommended that the ESR-1650T-3, when operated at either voltage, be connected to...rolls for the bend. NOTE: Deliberately setting the rolls non-parallel can the ... needed for a forming test run . Local codes take precedence over and re-feeding it releases...can be used to make sure it receives proper support as it exits the slip roll machine.
11.2...
User Manual - Page 10
Support the workpiece as it
nears the end (Figure 7a), stop the machine and raise the idler ...follows: 1. Figure 9
12.0 Maintenance
1. If a smaller radius is rotating counter-clockwise.
3. To make a complete loop of wire, use the instructions for a few drops of the rolls (see Figure 1).
10 Bend the wire using the same principles as needed , adjust the roll distance and re...
User Manual - Page 11
... and connections. 13.0 Troubleshooting the ESR-1650T Slip Roll
Trouble
Probable Cause
No incoming power. Workpiece is parallel to serve you call 1-800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com).
Idle Roll not engaging.
Tighten nut to make adjustments as needed.
14.0 Replacement Parts
Replacement parts are made when trying...
User Manual - Page 13
...4x1.5mm 230/460V-3PH ....... 1 ESR1650T/1-2-13 .......Power Cord for ESR-1650T
Index No Part No
Description
Size
Qty
1 ESR1650T-1 Side Cover 1 2 ESR1650T-2... TS-1532032 Phillips Pan Head Machine Screw M4x10 12 3 ESR1650T-3 Stand 1 4 ESR1650T-4 Left Support 1 5 ESR1650T-5 Right Support 1 6 ESR1650T-6 Rear Roll 1 7 ESR1650T-7 Upper Roll 1 8 ESR1650T-8 Safety Bracket 1...
User Manual - Page 14
...26 ........Bolt M5X25 3 18-27........ ESR1650T-18-30 ........Screw M4X8 3 18-31........ Index No Part No
Description
Size
Qty
18-14........ ESR1650T-18-22 ........Gear Shaft 1 18-23........ BB-6205...-31 Handle 4 32 ESR1650T-32 Pin ...4 33 ESR1650T-33 Bolt M12X55 1 34 TS-1524051 Set Screw M8x20 2 35 TS-1491021 Hex Cap Screw M10x20 5 36 ESR1650T-36 Bolt M12x25 4 ...
User Manual - Page 15
Index No Part No
Description
Size
Qty
57 TS-2246162 Socket Head Button Screw M6X16 5 58 TS-1505051 Socket Head Cap Screw M10x35 4 59 ESR1650T-59 Connecting Bushing 2 ...
User Manual - Page 16
15.1 Wiring Diagram for ESR-1650T-1
(Single Phase only)
16
User Manual - Page 17
15.2 Wiring Diagram for ESR-1650T-3
(Three Phase only)
17
JET Tools ESR-1650-1T Reviews
We have not received any reviews for JET Tools yet.