JET Tools JLP-025A-15 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JLP-025A-15 manuals!
Problems with JET Tools JLP-025A-15?
Ask a Question
Free JET Tools JLP-025A-15 manuals!
Problems with JET Tools JLP-025A-15?
Ask a Question
Popular JET Tools JLP-025A-15 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
JLP-A Series Manual Lever Hoists/Pullers
1/4- to 6-Ton
JLP-25A 1/4-ton
JLP-75A 3/4-ton
(models shown are representative of the series)
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-187505 Revision B1 12/2014 Copyright © 2014 JET
User Manual - Page 2
... OF OUR PRODUCTS. The specifications listed in Canada by calling 1-800-274-6846. Parts; Woodworking Machinery used for further clarification. JET Parallel clamps; VOLT Series Electric Hoists; Warehouse & Dock products;
How to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of an Authorized Service Center in interest to -date...
User Manual - Page 3
... 14 JLP-25A - Parts List...20 JLP-150A - Parts List...24 JLP-600A - Parts Breakdown 19 JLP-75A - Parts List...22 JLP-300A - Parts List...26 Ordering Parts ...28
3 Table of Contents
Warranty and Service...2 Table of Contents ...3 Introduction ...5 Specifications (JLP-25A, -50A) ...6 Specifications (JLP-75A, -150A, -300A, -600A) ...7 Unpacking ...8
Contents of the Carton ...8 Installation...
User Manual - Page 4
...repaired or replaced. 12. Never use . 5. Understand and follow all internal maintenance and inspections to comply with straight chain that use the hoist if either hook is twisted, kinked or damaged. 16. 1. Failure to a qualified JET service...to lift or support loads over sharp edges. If the lever is centered between top and bottom hooks. 17. Do not use the chain as set " over ...
User Manual - Page 5
... Lever Hoists/Pullers. Record your local supplier or JET. injury. The JLP-A Series hoists are proof-tested and comply with instructions set forth in accordance with OSHA, ANSI/ASME B30.21 and HST-3 standards.
This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.
If there are not heeded, it...
User Manual - Page 7
... indicates models with point ("shipyard") hooks; Capcy Lift (ton) (ft.)
Min. NOTE: The above stock numbers are available with slip clutch overload protection. specify when ordering.
7
Specify length when ordering. No. Specifications (JLP-75A, -150A, -300A, -600A)
Stock Number
Description
187606 JLP-75A-5 187607 JLP-75A-10 187608 JLP-75A-15 187609 JLP-75A-20 287606 JLP-75AWO...
User Manual - Page 8
... equal to, or greater than the capacity of the Carton
1 Lever Hoist 1 Owner's Manual 1 Warranty Card 1 Test Certificate
Installation
Support for the hoist may be installed by welding a second piece to the chain. See Figure 2 for set-up, maintenance and safety instructions. Replace the chain if links are stretched too long or seriously worn on page 11...
User Manual - Page 9
...repair of time, check for proper operation before resistance or gearing is designed, manufactured, and tested for an extended period of a hook by heat treating, bending or attaching anything by a JET authorized service center.
3. Inspecting Hooks
It is rotated in a clockwise direction. The brake mechanism must be replaced... Replace a hook immediately if any of the following problems ...
User Manual - Page 10
Set the top hook securely.
2. Move selector switch to raise or pull the load. Do not overload the lever hoist.
5. Avoid lifting one load...used either in front of each hoist must be equal to the total load to both hoists and use hoists with two hoists. Operation
The JLP Lever Hoist may be lifted. If this is dangerous to the operator, the lever hoist, and the load.
• Never load the hook...
User Manual - Page 12
...and the bearings in the model number). They are installed out-of-doors should not... 12
5 Links Limit
Replace if ≥
2.433" 2.433" 3.629" 4.838" 6.058" 6.058"
Hook Wear Limits (Top and Bottom)
Replace the hook when "A" in...repair to the load chain. Overload Protection
Some models of the JLP Lever Hoist have overload protection in the form of a slip clutch (these are available for your JET...
User Manual - Page 20
...-11 Change Over Spring 1 12 JLP75A-12 Spring Shaft 1 13 JLP75A-13 Change Over Pawl 1 15 JLP75A-15 Change Over Gear 1 *15L...........JLP75A-15L Overload Limiter Assembly 1 Overload Limiter Plate 1 Friction Disc A... 1 29 JLP75A-29 Roller Set (Right and Left 3x6 mm 66 30 JLP75A-30 Driving Pinion 1 31 JLP75A-31 Stripper ...1 32 JLP75A-32 Chain Guide Plate 1 34 JLP75A-34 ...
User Manual - Page 22
JLP-150A -
Part No. Parts List
Index No... (1.5T, 3T, 6T 1 13 JLP150A-13 Change Over Pawl (1.5T, 3T, 6T 1 15 JLP150A-15 Change Over Gear (1.5T, 3T, 6T 1 *15L...........JLP150A-15L Overload Limiter Assembly 1 Overload ...29 JLP150A-29 Roller Set (Right and Left 3x6 mm 74 30 JLP150A-30 Driving Pinion 1 31 JLP150A-31 Stripper ...1 32 JLP150A-32 Chain Guide Plate 1 34 JLP150A-...
User Manual - Page 24
Part No. Parts...6T 1 13 JLP150A-13 Change Over Pawl (1.5T, 3T, 6T 1 15 JLP150A-15 Change Over Gear (1.5T, 3T, 6T 1 *15L...........JLP300A-15L Overload...(3T, 6T) (s/n 12043550 and higher 1 29 JLP300A-29 Roller Set (Right and Left) (3T, 6T 5x6 mm 60 30 JLP300A... JLP300A-31 Stripper (3T, 6T 1 32 JLP300A-32 Chain Guide Plate (3T, 6T 1 34 JLP300A-34 Gear Side Plate Assembly...JLP-300A -
User Manual - Page 26
...1 13 JLP150A-13 Change Over Pawl (1.5T, 3T, 6T 1 15 JLP150A-15 Change Over Gear (1.5T, 3T, 6T 1 *15L...........JLP600A-15L Overload..., 6T) (s/n 120615109 and higher 1 29 JLP300A-29 Roller Set (Right and Left) (3T, 6T 5x6 mm 60 30 ...JLP300A-31 Stripper (3T, 6T 1 32 JLP300A-32 Chain Guide Plate (3T, 6T 1 34 JLP300A-34 Gear Side Plate ...Parts List
Index No.
Part No. JLP-600A -
User Manual - Page 28
Having the Model Number and Serial Number of your hoist available when you quickly and accurately.
427 New Sanford Road LaVergne, Tennessee 37086
Phone: 800-274-6848 www.jettools.com 28 Ordering Parts
To order parts or reach our service department, call will allow us to serve you call 1-800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com).
JET Tools JLP-025A-15 Reviews
We have not received any reviews for JET Tools yet.