JET Tools 354173 Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools 354173 manuals!
Problems with JET Tools 354173?
Ask a Question
Free JET Tools 354173 manuals!
Problems with JET Tools 354173?
Ask a Question
Popular JET Tools 354173 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
17" Floor Drill Press
Model: JDP-17DX
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-354173 Revision C3 11/2014 Copyright © 2014 JET
User Manual - Page 2
...parts or accessories expected to Get Technical Support Please contact Technical Service ... Pro-Duty Air Tools 2 Year - Manual Hoist Accessories;
The exceptions are acrylics and...Parts; Electric Hoists, Electric Hoist Accessories; VOLT Series Electric Hoists; Please contact Technical Service at any additional action needed. Please note that you specific legal rights, subject to parts...
User Manual - Page 3
......12 Table Tilt Adjustment ...12 Laser Adjustment ...13 Laser Assembly Removal/Installation 14 Lamp ...14 Operating Controls ...15 Basic Operation...15 Lubrication...15 Troubleshooting...16 Parts ...17 Ordering Replacement Parts ...17 Parts List...17 Assembly Drawing ...21 Wiring Diagram...22
The specifications in this manual are given as general information and are not binding. JET reserves the...
User Manual - Page 4
...
wrenches are specifically designed to...repaired or replaced. 18. Check damaged parts. A guard or other part that is damaged
should be carefully checked to these chemicals are not safety glasses. 7. Make your exposure to determine that is in use of exposure varies, depending on the machine and in a well-ventilated area and work . Read and understand the entire owners' manual...
User Manual - Page 5
...safety notices used in this manual:
This means that if...do not fall or lean against the spindle or other moving parts. Do not force a tool or attachment to do the...leave the machine running unattended.
Close the padlock. 4. Follow instructions for the best and safest performance. Familiarize yourself with care. ...servicing; improper accessories may result in serious injury.
24.
User Manual - Page 6
...any time and without prior notice, without incurring obligations. approx. (lbs.) ...215
The above specifications were current at our web site: www.jettools.com. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Overall Height (in.)...65 Base Size (in.)...12-1/2 x 19-5/8 Base Slots (W/in this...
User Manual - Page 7
Owner's Manual (1) -- Warranty Registration Card
Tools Supplied for Assembly
L 3mm Hex Wrench M 5mm Hex Wrench Tools Required for before attempting assembly! Clean all parts from the shipping container.
... Box Wrench or a 6"-8" Adjustable Wrench
Read and understand all assembly instructions before discarding any shortages or damage to comply may cause serious injury! Unpacking
Separate all ...
User Manual - Page 8
... (G) such that the teeth of the shaft (H) and tighten the setscrew (J) with the pinion gear on the base (A) and align the holes in the column support with the column (D) in the base.
3. It must be reinstalled later with the rack (F) onto the column (D) as shown and tighten the setscrew (C) with four...
User Manual - Page 9
...a steel hammer directly against a block of wood, to Figure 3: For right-handed operation, install three downfeed handles (B) into the hub on the arbor (C) engages the slot at the end...Place arbor (C) into the spindle (A). 6.
Tighten two set screws (A, Fig. 3) with a 5mm wrench until the tang (B) on the left -handed operation, install the downfeed handles into the downfeed hub (C) as shown....
User Manual - Page 10
... green with all local codes and ordinances. A temporary
adapter, which looks like the one heavy enough to run at 115-volt operation. When using an extension cord, be installed by a qualified electrician. Improper connection of the equipmentgrounding conductor can be sure to use one illustrated in Canada.
Repair or replace damaged or worn cord...
User Manual - Page 14
Unplug machine from the depth set bolt (H2).
4. Disconnect wiring connectors E1, E2.
This completes the removal of head.
Important: After installation, lasers must be connected to Figure 14:
1. This completes the laser assembly installation. Figure 14
14 Remove nuts (A, C), and washer (B) from the power source.
2. With a 5mm hex wrench, loosen the socket head...
User Manual - Page 16
...Drill Press vibrates excessively.
Probable Cause 1. Bit or chuck not installed properly. 1. Check all mating surfaces thoroughly with adequate size and length cord.
2. Replace cord. 4. Resharpen bit correctly. 2. Support or clamp workpiece. 2.
Tighten set screws in workpiece. Troubleshooting
Trouble Drill press will not start.
Bit sharpened incorrectly. 2. Remedy...
User Manual - Page 17
...Parts
Ordering Replacement Parts
To order parts or reach our service department, call will allow us to serve you quickly and accurately. Having the Model Number and Serial Number of your machine available when you call 1-800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). Parts List
Index No Part... Ring 1 20 TS-1523021 Set Screw M6x8 1 21 12909001 ...
User Manual - Page 18
Parts List
Index No Part No
Description
Size
Qty
41 10661102 Seat ...1 42 13005601 Washer 1 43 13005701 ...1532032 Pan Head Machine Screw M4x8 4 59 TS-1504051 Socket Head Cap Screw M8x25 1 60 TS-1523011 Socket Set Screw M6x6 8 61 JDP17DX-061 ..........Handle Assembly (Set of 3) (includes # 62,63 1 62 JDP17DX-062 ..........Handle Bar 3 63 JDP17DX-063 ..........Handle Grip ...
User Manual - Page 19
...Switch Box 1 140........... TS-1533032 Pan Head Machine Screw M5x10 4 145........... Parts List
Index No Part No
Description
Size
Qty
95 JDP17DX-095 ..........Rubber Seal 1 96 JDP17DX-096 ...Collar Dia.50 1 104........... 10706508A1 Driving Sleeve 1 105........... 10606904 Pulley Set Nut 1 106........... JDP17DX-108 ..........Motor Pulley 1 109........... TS-0733031 External...
JET Tools 354173 Reviews
Do you have an experience with the JET Tools 354173 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!