Instruction Manual
Page 4
CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this equipment does cause harmful interference to radio or television reception, which the receiver is connected. • ... occur in a residential installation. cian for a Class B digital device, pursuant to part 15 of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and re- If this device under FCC regulations. iii These limits are designed to provide reasonable protection against...
CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this equipment does cause harmful interference to radio or television reception, which the receiver is connected. • ... occur in a residential installation. cian for a Class B digital device, pursuant to part 15 of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and re- If this device under FCC regulations. iii These limits are designed to provide reasonable protection against...
Instruction Manual
Page 6
... Do not transmit with gain not greater than the allowable MPE level set by a grounded metallic barrier. For watercraft without suitable structures, the antenna must be mounted a WARNING minimum of 5 meters (measured from the lowest point of the 3 meter MPE radius. v FAILURE TO OBSERVE ... RF exposure compliance requirements. RADIO OPERATOR WARNING Icom requires the radio operator to the height of the antenna, unless such persons (such as to maintain a minimum of 1 meter vertically between the antenna, (measured from the lowest point of the antenna), to the heads of all persons AND ...
... Do not transmit with gain not greater than the allowable MPE level set by a grounded metallic barrier. For watercraft without suitable structures, the antenna must be mounted a WARNING minimum of 5 meters (measured from the lowest point of the 3 meter MPE radius. v FAILURE TO OBSERVE ... RF exposure compliance requirements. RADIO OPERATOR WARNING Icom requires the radio operator to the height of the antenna, unless such persons (such as to maintain a minimum of 1 meter vertically between the antenna, (measured from the lowest point of the antenna), to the heads of all persons AND ...
Instruction Manual
Page 7
... n Automatic acknowledgement 43 n Offset time 43 7 SET MODE 44-47 n Set mode programming 44 n Set mode items 45 8 CONNECTIONS AND MAINTENANCE 48-51 n Connections 48 n Antenna 49 n Fuse replacement 49 n Cleaning 49 n Mounting the transceiver 50 n Optional MB-69 installation 51 9 TROUBLESHOOTING 52 10 SPECIFICATIONS AND OPTION 53-55 n Specifications 53...
... n Automatic acknowledgement 43 n Offset time 43 7 SET MODE 44-47 n Set mode programming 44 n Set mode items 45 8 CONNECTIONS AND MAINTENANCE 48-51 n Connections 48 n Antenna 49 n Fuse replacement 49 n Cleaning 49 n Mounting the transceiver 50 n Optional MB-69 installation 51 9 TROUBLESHOOTING 52 10 SPECIFICATIONS AND OPTION 53-55 n Specifications 53...
Instruction Manual
Page 15
... 10 cm from the speaker. • Further adjustment of your mouth and speak into the micro- BASIC OPERATION 3 n Receiving and transmitting CAUTION: Transmitting without an antenna may be necessary. y Hold down 3 [PTT], hold the microphone 5 to select the output power, if necessary. • "LOW" appears when low power is selected. •...
... 10 cm from the speaker. • Further adjustment of your mouth and speak into the micro- BASIC OPERATION 3 n Receiving and transmitting CAUTION: Transmitting without an antenna may be necessary. y Hold down 3 [PTT], hold the microphone 5 to select the output power, if necessary. • "LOW" appears when low power is selected. •...
Instruction Manual
Page 56
... (Red) Connect a GPS receiver for plotting position data received from other equipment occurring. Rubber vulcanizing tape y ANTENNA CONNECTOR Connect a marine VHF antenna with rubber vulcanzing tape, as shown below, to the transceiver. CAUTION: Transmitting without an antenna may damage the transceiver. Use a PH M3 × 6 mm screw (not supplied). w EXTERNAL SPEAKER LEAD (Yellow...
... (Red) Connect a GPS receiver for plotting position data received from other equipment occurring. Rubber vulcanizing tape y ANTENNA CONNECTOR Connect a marine VHF antenna with rubber vulcanzing tape, as shown below, to the transceiver. CAUTION: Transmitting without an antenna may damage the transceiver. Use a PH M3 × 6 mm screw (not supplied). w EXTERNAL SPEAKER LEAD (Yellow...
Instruction Manual
Page 57
...OUT (−) Connects to the MA-500TR class b ais transponder using the transponder without entering the target's MMSI code. * OPC-2014 is the antenna. 8 CONNECTIONS AND MAINTENANCE D Connect to the MA-500TR Connect the transceiver to lead 4 of OPC-2014. Outer conductor: NMEA IN (−) ...16 DO NOT use harsh solvents such as benzine or alcohol, as they will damage transceiver surfaces. 49 n Antenna 1 2 A key element in the supplied DC power cable. Ask your dealer about antennas and 3 the best place to mount them. 4 n Fuse replacement 5 6 A fuse is installed in ...
...OUT (−) Connects to the MA-500TR class b ais transponder using the transponder without entering the target's MMSI code. * OPC-2014 is the antenna. 8 CONNECTIONS AND MAINTENANCE D Connect to the MA-500TR Connect the transceiver to lead 4 of OPC-2014. Outer conductor: NMEA IN (−) ...16 DO NOT use harsh solvents such as benzine or alcohol, as they will damage transceiver surfaces. 49 n Antenna 1 2 A key element in the supplied DC power cable. Ask your dealer about antennas and 3 the best place to mount them. 4 n Fuse replacement 5 6 A fuse is installed in ...
Instruction Manual
Page 59
... a hole into the instrument panel (or wherever you plan to mount the transceiver.) w Slide the transceiver through the hole as shown below . 13 y Connect the antenna and power cable, then return the instrument control panel to its original place. 14 15 16 t r 51 strument control panel. 11 t Tighten the locking nuts...
... a hole into the instrument panel (or wherever you plan to mount the transceiver.) w Slide the transceiver through the hole as shown below . 13 y Connect the antenna and power cable, then return the instrument control panel to its original place. 14 15 16 t r 51 strument control panel. 11 t Tighten the locking nuts...
Instruction Manual
Page 61
... rejection ratio : More than 70 dB 15 • Spurious response rejection ratio : More than 70 dB • Adjacent channel selectivity : More than 40 dB 9 • Antenna impedance : 50 ø nominal • Input impedance (MIC) : 2 kø • Audio frequency response: +1 to -3 dB of 6 dB/octave range from 300 to change without notice...
... rejection ratio : More than 70 dB 15 • Spurious response rejection ratio : More than 70 dB • Adjacent channel selectivity : More than 40 dB 9 • Antenna impedance : 50 ø nominal • Input impedance (MIC) : 2 kø • Audio frequency response: +1 to -3 dB of 6 dB/octave range from 300 to change without notice...