Icom IC-F3001 Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-F3001 manuals!
Problems with Icom IC-F3001?
Ask a Question
Free Icom IC-F3001 manuals!
Problems with Icom IC-F3001?
Ask a Question
Popular Icom IC-F3001 Manual Pages
Instruction Manual - Page 1
The photo shows the VHF transceiver. Limited functions only
INSTRUCTION MANUAL VHF TRANSCEIVERS
iF3000
Series
UHF TRANSCEIVERS
iF4000
Series
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this device does not cause harmful interference.
Instruction Manual - Page 2
... only.
Personal injury, fire hazard or electric shock may occur.
SAVE THIS INSTRUCTION MANUAL- i CAUTION NOTE
DEFINITION Personal death, serious injury or an explosion may occur. PREFACE
READ ALL INSTRUCTIONS carefully and completely before
using the transceiver.
Icom is not responsible for the IC-F3001/IC-F3003 VHF TRANSCEIVERS and the IC-F4001/IC-F4003 UHF TRANSCEIVERS.
Instruction Manual - Page 3
... expressly approved by Icom Inc., could void your authority to operate this equipment in a residential area is operated in accordance with the limits for a Class A digital device, pursuant to part 15 of this transceiver under FCC regulations. FCC INFORMATION
This equipment has been tested and found to comply with the instruction manual, may cause...
Instruction Manual - Page 6
... 8 3 BASIC OPERATION 12-22 ■ Turning power ON 12 ■ Channel selection 13 ■ Call procedure 14 ■ Receiving and transmitting 15 ■ Setting the microphone gain 18 ■ Setting the squelch level 19 ■ Output power level selection 20 ■ Priority A channel selection 20 ■ MDC 1200 system operation 20 ■ Emergency Call...
Instruction Manual - Page 12
2 PANEL DESCRIPTION
■ Front, top and side panels
i ANTENNA
CONNECTOR
q ROTARY
SELECTOR
w VOLUME
CONTROL
e LED INDICATOR
u PTT SWITCH
y UPPER KEY t LOWER KEY
Speaker
r SPEAKER-
w VOLUME CONTROL [VOL] Rotate to select the pre-programmed memory channels. MICROPHONE JACK
Microphone
q ROTARY SELECTOR Rotate to turn the power ON/OFF, and adjust the audio level.
5
Instruction Manual - Page 14
...8226; TX low Battery 2: Very Low Battery was detected during TX mode. G
• Call LED (ON): Turns ON while receiving a matched 2/5-tone.
w BATT 2
R*
R*
R*
R*
• Channel Error: A non-programmed channel is activated.
can
G
G
• Low Battery 1: You should charge the battery. (blinks slowly)
B AT T1
G G
• Low Battery 2: You must charge the battery. (blinks fast...
Instruction Manual - Page 15
... keys.
3
Consult your Icom dealer or system operator for details concerning
your dealer for 1 sec. 16
to assign the operating channel to pause
the scanning operation... nel, respectively.
17
MEMORY CHANNELS 1, 2, 3, 4
18
Push to directly select memory channel 1, 2, 3 or 4, if programmed. 19
Consult your transceiver's programming.
4
SCAN A
5
➥ Push to start and ...
Instruction Manual - Page 17
...Talk Around function equalizes the transmit frequency to the receive frequency for details.
7
➥ Push and hold to turn the Talk Around function OFF.
➥ Push and hold to switch the IF bandwidth to Narrow.
8
DTMF AUTODIAL Push to transmit a programmed DTMF code.
9
10
CALL, CALL ... width can be selected from 20 or 25 kHz using the optional cloning software (PMR operation only).
Instruction Manual - Page 19
q Set [ROTARY SELECTOR] to any [ROTARY SELECTOR] 11
channel other than Channel 16.
[VOL] 12
w Rotate [VOL] to r until you select the attached battery type.
20
NOTE: This operation may not be selected according to the battery ...
Instruction Manual - Page 20
....
13 Scanning stops when a call is not necessary for this type. NOTE: If the Move to your system set up. 3 BASIC OPERATION
■ Channel selection
Several types of memory channel keys, [MR-CH 1] to [MR-CH 4]. To select a desired operating channel, do one of the following. • Rotate [ROTARY SELECTOR]. • Push one of...
Instruction Manual - Page 27
... 3 beeps sound when "High" is selected.
8
9
■ Priority A channel selection
10
Depending on the presetting.
3
When the battery case is programmed. It allows PTT ID* and Emergency signaling. *When [PTT] is pushed and...'s Emergency feature can be selected, depending on the presetting, the Priority A channel is selected each time the transceiver power is turned ON.
11
12
■...
Instruction Manual - Page 28
... dealer for details.
21
IMPORTANT: It is programmed for Silent operation, you can transmit an Emergency call transmission, the transceiver stands by in the audible mode for the specified time period.*
* Depending on the previously selected channel.
Ask your transceiver is recommended to set an emergency channel individually to cancel the emergency call, push...
Instruction Manual - Page 33
... into contact with fluid from inside the battery gets in this instruction manual.
4
R DANGER! This could occur if the battery is ...to +60˚C (-4˚F to rupture.
If any part of these
conditions occur, contact your eyes with the transceiver ...in your eyes, blind- 5
ness can result. Rinse your Icom dealer or distributor.
8
R WARNING!
tery may cause heat ...
Instructions - Page 1
... (RF), en mode de transmission. Icom, Icom Inc. This device complies with the instruction manual, may cause smoke, fire, or cause the battery to the transceiver) into the charger if it safely in RF exposure levels exceeding the FCC and IC requirements for wireless RF exposure.
••H ealth Canada Safety Code 6 - RRWARNING! RRWARNING! CAUTION: DO...
Instructions - Page 2
... code is... holds is supplied) Approximately 16 hours for the IC-F3000 series and the IC-F4000 series.
A power
adapter may be used ...is turned ON, and the operating periods are installed in some functions to the transceiver. BC-197...BASIC OPERATION
DDTurning ON the transceiver
NOTE: Before using reverse polarity. Select a channel.
TX : RX : standby = 5 : 5 : 90
DDCHARGERS
•&#...
Icom IC-F3001 Reviews
We have not received any reviews for Icom yet.