Instruction Manual
Page 20
... !0 !8 !5 !1 !7 o !0 w !1 e !2 !3 !4 !3 !2 !6 !5 q S/RF METER (pgs. 35, 126) Shows the signal strength while receiving. Shows the relative output power, SWR, ALC, VD, ID or compression levels while transmitting. • A total of the IF filter. t SHIFT FREQUENCY INDICATOR (p. 75) Shows the shift frequency of 3 meter types are available. • Standard meter • Edgewise meter...RTTY or PSK operation. u BANDPASS FILTER INDICATOR Appears when the narrow filter (500 Hz or less) is in time set in use. r BANDWIDTH INDICATOR (p. 75) Shows the passband width of the IF filter.
... !0 !8 !5 !1 !7 o !0 w !1 e !2 !3 !4 !3 !2 !6 !5 q S/RF METER (pgs. 35, 126) Shows the signal strength while receiving. Shows the relative output power, SWR, ALC, VD, ID or compression levels while transmitting. • A total of the IF filter. t SHIFT FREQUENCY INDICATOR (p. 75) Shows the shift frequency of 3 meter types are available. • Standard meter • Edgewise meter...RTTY or PSK operation. u BANDPASS FILTER INDICATOR Appears when the narrow filter (500 Hz or less) is in time set in use. r BANDWIDTH INDICATOR (p. 75) Shows the passband width of the IF filter.
Instruction Manual
Page 71
NOTE: When data mode is selected, the audio input from the [ACC1] (pin 4) is selected. sion as follows: • [COMP] : OFF • Tx bandwidth : MID* • Tx Tone (Bass) : 0 • Tx Tone (Trebles) : 0 *Fixed to the default value (lower: 300, higher: 2700). (p. 122) ✔ ...is displayed when SSB data mode is used for transmis- ating mode. t R otate the main dial to tune to transmit. • When operating in step e for 1 sec. 4 RECEIVE AND TRANSMIT ■ Data mode (AFSK) operation When operating AMTOR or PACKET with the TNC and/or the software. r P ...
NOTE: When data mode is selected, the audio input from the [ACC1] (pin 4) is selected. sion as follows: • [COMP] : OFF • Tx bandwidth : MID* • Tx Tone (Bass) : 0 • Tx Tone (Trebles) : 0 *Fixed to the default value (lower: 300, higher: 2700). (p. 122) ✔ ...is displayed when SSB data mode is used for transmis- ating mode. t R otate the main dial to tune to transmit. • When operating in step e for 1 sec. 4 RECEIVE AND TRANSMIT ■ Data mode (AFSK) operation When operating AMTOR or PACKET with the TNC and/or the software. r P ...
Instruction Manual
Page 73
... the current spectrum waveform. • " " appears while the function is selected. The scope bandwidth can be specified for each frequency band independently in this mode. 4 RECEIVE AND TRANSMIT D Fixed mode Displays signals within the specified frequency range. to select the scope screen. tivated.... • 10, 20 and 30 dB attenuators are displayed in the background of range. • The spectrum scope shows the transmit signal while transmitting. e P ush [CENT/FIX] (F-5) several times to close a multi- r P ush [ATT] (F-2) several times to clear the...
... the current spectrum waveform. • " " appears while the function is selected. The scope bandwidth can be specified for each frequency band independently in this mode. 4 RECEIVE AND TRANSMIT D Fixed mode Displays signals within the specified frequency range. to select the scope screen. tivated.... • 10, 20 and 30 dB attenuators are displayed in the background of range. • The spectrum scope shows the transmit signal while transmitting. e P ush [CENT/FIX] (F-5) several times to close a multi- r P ush [ATT] (F-2) several times to clear the...
Instruction Manual
Page 120
... automatically tune correctly. After the tuner matches an antenna, the variable capacitor settings are memorized as follows: [Example]: Suppose you have a narrow bandwidth. nected to antenna port in some cases.) q S et 3.55 MHz and push and hold [TUNER] for each frequency range (100 kHz ...an antenna properly con- ing farther than 2.5:1 for 50 MHz band) • the transmit power. (8 W for HF bands; 15 W for 50 MHz band) • the power source voltage/capacity. ❍ Tuning a narrow bandwidth antenna Some antennas, especially for HF bands; In such cases, push and hold [TUNER] ...
... automatically tune correctly. After the tuner matches an antenna, the variable capacitor settings are memorized as follows: [Example]: Suppose you have a narrow bandwidth. nected to antenna port in some cases.) q S et 3.55 MHz and push and hold [TUNER] for each frequency range (100 kHz ...an antenna properly con- ing farther than 2.5:1 for 50 MHz band) • the transmit power. (8 W for HF bands; 15 W for 50 MHz band) • the power source voltage/capacity. ❍ Tuning a narrow bandwidth antenna Some antennas, especially for HF bands; In such cases, push and hold [TUNER] ...
Instruction Manual
Page 163
... 01 Frequency stamp for RTTY time stamp ON 0149 see p. 158 Send/read received text font color for RTTY decoder 0150 see p. 158 Send/read transmitted text font color (RTTY) 0151 see p. 158 Send/read time stamp text font color (RTTY) 0152 see p. 158 Send/read text font color...0000=0%, 0255=100%) 06 see p. 158 Send/read DATA mode with filter set 07 00 WIDE selection for SSB transmit bandwidth 01 MID selection for SSB transmit bandwidth 02 NAR selection for SSB transmit bandwidth 08 00 SHARP selection for DSP filter type 01 SOFT selection for DSP filter type 09 00 3 kHz roofing filter...
... 01 Frequency stamp for RTTY time stamp ON 0149 see p. 158 Send/read received text font color for RTTY decoder 0150 see p. 158 Send/read transmitted text font color (RTTY) 0151 see p. 158 Send/read time stamp text font color (RTTY) 0152 see p. 158 Send/read text font color...0000=0%, 0255=100%) 06 see p. 158 Send/read DATA mode with filter set 07 00 WIDE selection for SSB transmit bandwidth 01 MID selection for SSB transmit bandwidth 02 NAR selection for SSB transmit bandwidth 08 00 SHARP selection for DSP filter type 01 SOFT selection for DSP filter type 09 00 3 kHz roofing filter...