Icom F5021 / F6021 Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom F5021 / F6021 manuals!
Problems with Icom F5021 / F6021?
Ask a Question
Free Icom F5021 / F6021 manuals!
Problems with Icom F5021 / F6021?
Ask a Question
Popular Icom F5021 / F6021 Manual Pages
Instruction Manual - Page 2
... NOTE
Equipment damage may occur. No risk of their respective holders.
This
instruction manual contains important operating instructions for the IC-F5021, IC-F5023/H, IC-5026/H, IC-F5028H VHF MOBILE TRANSCEIVERS and the IC-F6021, F6023/H, F6028H UHF MOBILE TRANSCEIVERS.
Icom, Icom Inc. These limits are registered trademarks of the FCC Rules. EXPLICIT DEFINITIONS
tee...
Instruction Manual - Page 7
...start and cancel scanning operation.
3
Consult your Icom dealer or system operator for priority channel), ...Programmable function keys
1
The following explanations, the specific key is "zone"?- to indicate the scan list...10149; Push to select a transmit code channel after pushing [TX Code CH Select].
The scan restarts ...setting, the cleared channel is added
to select an operating channel.
Instruction Manual - Page 10
...Push to turn the Ext. SCRAMBLER KEY ➥ P ush to select a TX code channel directly. User set the desired digit using [CH Up]/ [CH Down].
• Up to turn... for 1 sec. 1 PANEL DESCRIPTION
TX CODE CHANNEL SELECT KEY ➥ Push to enter the TX code edit mode. Then
set mode items are memorized. ➥ Push and hold this case, all set the desired channel using [CH Up]/[CH Down...
Instruction Manual - Page 11
....
3
input the digit codes as directed by your dealer. • The keys as identical. Channel setting is programmed for a start over in this type.
channel, in the same block as below can be incorrect. Methods
w If the transceiver is not necessary for password input:
NON-ZONE TYPE:
4
The transceiver detects numbers in sequence; or...
Instruction Manual - Page 12
... specific station(s) only and prevents unwanted stations from
your dealer for the specified time period* when a matched RX code ...from contacting you to your signal;
1. NOTE: Depending on the pre-setting, the transceiver automatically transmits the microphone audio for details. Ask your mouth... your System Operator's instructions.
• This may be necessary depending on programming.
•...
Instruction Manual - Page 13
... pushed (beginning of the
15
transmission) and/or released (end of transmission) de-
16
pending on the pre-setting)
5
USING [TX CODE CH SELECT] KEY:
q P ush [TX Code CH Select]- BASIC OPERATION 2
D Transmitting notes
D TX code channel selection
1
• Transmit inhibit function The transceiver has several inhibit functions which restrict
If the transceiver has...
Instruction Manual - Page 14
... right will
blink automatically. ited. u After editing, push [TX Code CH Select] to set .
• Return to transmit the DTMF code.
10
USING [TX CODE ENTER] KEY: q P ush [TX Code Enter] to enter the TX code edit mode.
• The digit to be edited blinks.
e P ush [TX Code CH Select] to select the desired digit to be...
Instruction Manual - Page 15
... used items with 'Power ON' function. to turn power OFF, then ON
again to exit set mode:
q W hile pushing and holding [P1] and [P2], push [ ] to set mode functions are available.
Entering the user set mode.
[P1] [P2] [ ]
w P ush and hold [ ] for instructions regarding using a programmable key. Then, push [Up] or [Down] to p. 6 [User...
Instruction Manual - Page 16
... MDC 1200 signaling system. (p. 13)
■ Priority A channel selection
When one of the password (p. 8) or receiving a specified ID, set as a revive ID, is selected each time the trans- ceiver power is turned ON. &#...with the MDC 1200 signaling system. (p. 13)
■ Stun function
When the specified ID, set as a stun ID or kill ID, is received, the stun function is transmitted once or ...
Instruction Manual - Page 17
...signaling,
The MDC 1200 system Emergency feature can be accessed
3
and receiving Radio Check.
Aliasing allows the substitution of an
acknowledgement signal.
6
alphanumeric name for... it receives the
5
transceivers is programmed.
For receive, the alias of MDC 1200 system found in Icom
edly for re- to call , etc.
BASIC OPERATION 2
■ MDC 1200 system operation
1
...
Instruction Manual - Page 19
... supplied with your trans- ■ Supplied Accessories
Microphone
Microphone hanger Microphone
and screw set
hanger cable
DC power cable
Function name stickers*
Mounting bracket
Flat washers
Nuts
Mounting ...×20)
*Used for labelling the programmable function keys according to a thick surface which can support more than 1.5 kg
(3.3 lb).
5
6
Flat washer
7
8
9
10
Felt*
Spring...
Instruction Manual - Page 20
...installed in each fuse holder of the supplied DC power cable*. If a fuse blows or the transceiver stops functioning, track down the source of the problem if possible, and then replace...m (23 ft)
■ Fuse replacement
• OPC-1939 acc cable Allows you to connect to -install.
■ Cleaning
• UT-108R dtmf decoder unit Provides pager and code squelch capabilities. SP-22 : Compact ...
Instruction Manual - Page 21
...Icom radio generates RF electromagnetic en-
3. IC-F5021:
1
ergy during the course of employment by the "General
the properly installed antenna. recommended minimum distance of the hazards, and the ways to bystanders.
17 This radio... of the vehicle in order to protect against exposure to bystanders. 2. IC-F6021:
14
The antenna is required to be located outside of a vehicle and
15...
Instruction Manual - Page 22
... is the antenna supplied with this radio by the manufacturer or an antenna specifically authorized by pressing the "PTT" switch. You can cause the radio to be exceeded.
DO NOT operate the transmitter in areas where signs are sensitive to electromagnetic radiation such as this may damage the radio and may also cause you...
Analog Mobiles Comparison Chart - Page 1
...Icom America Inc. The Icom logo is a registered trademark of Icom Inc. AT-A-GLANCE
Analog Mobile Radio Comparison
F5011
Entry level analog mobile
F5021... Full analog signaling (2/5 tone, MDC1200)
• LTR built-in
• Upgradeable to 6.25 digital
• Detachable front panel
• DB-25 connector
&#... or drawing any specific application is claimed or asserted in inversion voice scrambler...
Icom F5021 / F6021 Reviews
We have not received any reviews for Icom yet.