IBM 87302RU Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 87302RU Manual Pages
Hardware Maintenance Manual - Page 41
...controller 2 to the other. The management module has a separate internal 100 Mbps link to set any jumpers or configure the controller for data packets to flow from application programs on the blade...no internal data path between the management module and a service processor on each blade server. Chapter 2. must install a device driver on the blade server to enable the blade server ...
Hardware Maintenance Manual - Page 52
... Maintenance Manual and Troubleshooting Guide There are present inside these parts, contact a service technician. Remove the bezel assembly from the front of these components. If you suspect a problem with your module or option. If you are installing or removing a module at the front of the
BladeCenter T unit (see the illustration on page 40. Note: These instructions assume...
Hardware Maintenance Manual - Page 61
... and installing management modules
The BladeCenter T unit comes with the service processor in each blade server for functions such as: v Blade server power-on page 10 for information about the controls and indicators. You can send the VGA signal stream to detect presence or absence and any error conditions, sending alerts when required. Setting up...
Hardware Maintenance Manual - Page 71
...support the network interface that the ports on the blade server I /O-module bays 3 and 4. Note the designation that a blade server uses through your operating-system settings.
2. The other Ethernet controller in this section to the switch module or pass-thru module.
Use the instructions... b. c. Ping an external computer on the network that you have installed an I/O expansion option on ...
Hardware Maintenance Manual - Page 74
... BladeCenter T Type 8720 and 8730: Hardware Maintenance Manual and Troubleshooting Guide Attention: To maintain proper system cooling, do not operate the BladeCenter T unit for more than the one from which it was removed could have unintended consequences. Removing and installing a blade server or filler module
Use the instructions in each blade bay.
You might be...
Hardware Maintenance Manual - Page 99
... unit has the latest level of firmware code installed. Note: Try reseating a suspected component or reconnecting a cable before using the troubleshooting charts: 1.
Run the diagnostic tests to see if the problem has been corrected before you have available when servicing the system.
If you replace a FRU. Error symptoms
You can cause false errors and symptoms.
2. The most likely...
Hardware Maintenance Manual - Page 100
...eventually turn The problem occurs after installing the second microprocessor...8730: Hardware Maintenance Manual and Troubleshooting Guide Some components do not have these items installed or have environmental ...set and stepping level must be used as follows:
1. Switching KVM control between blade servers until the mouse and keyboard are both working on , the amber system-error replacing...
Hardware Maintenance Manual - Page 102
... to set the VESA video mode to modify the XF86Config file (/etc/X11/XF86Config);
During an unattended network install, the YaST program uses the AutoYaST control file to 1040x768@60Hz. OR -- Troubleshooting charts (continued)
Device
Suggested action
Remote control does not work for min_vsync to 60. Other operating systems do not exhibit the problem...
Hardware Maintenance Manual - Page 104
...settings for the switch module to the management module NVRAM; When you are running Windows 2000. Update the diagnostics on the back of the screen. When troubleshooting Ethernet-related problems, make sure that the Ethernet cables on a blade server 4.
Updating... T Type 8720 and 8730: Hardware Maintenance Manual and Troubleshooting Guide If the two IP addresses are connected properly...
Hardware Maintenance Manual - Page 107
... detected during SuSE installation.
The steps for selecting the mouse are connected to the DC power
terminals at http://www.ibm.com/pc/support/. If the problem remains, replace the option. You will need to "Undetermined problems" on the screen, widely
and running X Windows
when using the remote console on a blade server that : 1. Table 6.
Troubleshooting charts (continued)
Device...
Hardware Maintenance Manual - Page 114
... T Type 8720 and 8730: Hardware Maintenance Manual and Troubleshooting Guide Damaged data in this section if the diagnostic tests did not identify the failure, the devices list is incorrect, or the system is a blade server problem. Message
Action
Failure reading I2C device. Check devices on bus 5.
1. Reseat the power modules. 2. Replace the management module. 5. Reseat the...
Installation Guide - Page 39
..., if present, provides redundancy. The latest level of management-module firmware is switched to the redundant management module. The service processor in the management module communicates with the service processor in each blade server to support features such as blade server power-on requests, error and event reporting, KVM requests, and requests to use by a local...
Installation Guide - Page 64
...Installation Guide Application considerations
Information about installing any jumpers or configure the controller for the BladeCenter T unit have device drivers that comes with your operating system go to address the Ethernet controller. Operating system considerations
The following Web site: www.ibm.com/pc/support.
Device driver... do not need to set any required device drivers.
Installation Guide - Page 94
...specific default VLAN ID for the download configuration file, firmware code file, upload configuration file, and log file. Virtual LANs
Virtual LANs (VLANs) allow multiple blade servers to support this configuration. When VLANs are set... 8720 and 8730: Planning and Installation Guide
If multiple VLANs are in the... both Ethernet switches for TFTP services to non-volatile random access ...
Installation Guide - Page 100
... that connect to the IBM Support Web site: www.ibm.com/pc/support for your the BladeCenter T unit. Go to the server blades in this section along with the update. You can install two fibre-channel switch modules in the IBM BladeCenter HS20 Type 8832 Installation and User's Guide and IBM BladeCenter HS40 Type 8839 Installation and User's Guide. Fibre-channel switch...
IBM 87302RU Reviews
We have not received any reviews for IBM yet.