Owners Manual
Page 6
...10003; All assembly instructions have been completed. ✓ No remaining loose parts in a well-ventilated area. See that follow all belt keepers. ✓ Check wiring. WARNING: Before starting and transmission purging instructions (See "TO START ENGINE" and "PURGE TRANSMISSION" ...10003; All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory). ✓ Be sure mower deck is important to its highest position. • Releaseparkingbrakebydepressingclutch/brakepedal. • Place freewheel control in "transmission disengaged" position (See "...
...10003; All assembly instructions have been completed. ✓ No remaining loose parts in a well-ventilated area. See that follow all belt keepers. ✓ Check wiring. WARNING: Before starting and transmission purging instructions (See "TO START ENGINE" and "PURGE TRANSMISSION" ...10003; All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory). ✓ Be sure mower deck is important to its highest position. • Releaseparkingbrakebydepressingclutch/brakepedal. • Place freewheel control in "transmission disengaged" position (See "...
Owners Manual
Page 22
...way down and engage parking brake. • Disengage transmission by placing freewheel control in installing the deck belt, refer to the routing decal on both mandrel housings and secure with fasteners. MOWER DRIVE BELT INSTALLATION (See Fig. 31 & 32) NOTE: For ease in "transmission disengaged" position. Correct ...than five (5) feet to make sure it is enough slack, slip the belt onto the center spindle pulley. SPRING EYEBOLT NUT IDLER ARM Fig. 30 • Remove the belt from around mandrels and entire upper deck surface. • With a 3/8" breaker bar and using the square opening...
...way down and engage parking brake. • Disengage transmission by placing freewheel control in installing the deck belt, refer to the routing decal on both mandrel housings and secure with fasteners. MOWER DRIVE BELT INSTALLATION (See Fig. 31 & 32) NOTE: For ease in "transmission disengaged" position. Correct ...than five (5) feet to make sure it is enough slack, slip the belt onto the center spindle pulley. SPRING EYEBOLT NUT IDLER ARM Fig. 30 • Remove the belt from around mandrels and entire upper deck surface. • With a 3/8" breaker bar and using the square opening...
Owners Manual
Page 27
...4. Clean around mandrels. 1. Shift to open vent holes. Clean underside of grass, leaves, trash under mower. 7. Replace mower drive belt. 9. Replace with attachment clutch engaged 1. of drive 1. Check wiring and connections. 5. Bad battery cell(s). 2. Faulty alternator. 1. Replace... equipped). 4. Debris on steering plate (if equipped). 3. Motion drive belt worn, damaged, or broken. 4. Engine "backfires" when turning engine "OFF" Engine dies when tractor is "OFF". 2. CORRECTION 1. Mower deck not level. 3. Clean underside of mower housing. 4. Replace blade....
...4. Clean around mandrels. 1. Shift to open vent holes. Clean underside of grass, leaves, trash under mower. 7. Replace mower drive belt. 9. Replace with attachment clutch engaged 1. of drive 1. Check wiring and connections. 5. Bad battery cell(s). 2. Faulty alternator. 1. Replace... equipped). 4. Debris on steering plate (if equipped). 3. Motion drive belt worn, damaged, or broken. 4. Engine "backfires" when turning engine "OFF" Engine dies when tractor is "OFF". 2. CORRECTION 1. Mower deck not level. 3. Clean underside of mower housing. 4. Replace blade....
Owners Manual
Page 41
...Wash 5/16 Slw Wheel, Gauge Bolt, Shoulder Arm, Susp., Rear Nut, 3/8-16 Hex Jam Nyloc Sb 3/8-16 x 3/8 Skt Hd Washer, 3/8 Sae Flt Belt, 42" Fab Deck Guard, Belt Pulley, Mandrel Hcs 7/16-14 x 2-1/2 Gr. 5 Washout Port Bolt, 1/4-20 x 1/2 Eyebolt 5/16 x 3-1/2 Spring Nut 5/16-18 Hex Whizlk Ball... Bearing Pulley Retainer Clip Mower Deck Complete NOTE: All component dimensions given in U.S. YTH22V42LS (96043011300), PRODUCT NO. 960 43 01-13 MOWER DECK KEY...
...Wash 5/16 Slw Wheel, Gauge Bolt, Shoulder Arm, Susp., Rear Nut, 3/8-16 Hex Jam Nyloc Sb 3/8-16 x 3/8 Skt Hd Washer, 3/8 Sae Flt Belt, 42" Fab Deck Guard, Belt Pulley, Mandrel Hcs 7/16-14 x 2-1/2 Gr. 5 Washout Port Bolt, 1/4-20 x 1/2 Eyebolt 5/16 x 3-1/2 Spring Nut 5/16-18 Hex Whizlk Ball... Bearing Pulley Retainer Clip Mower Deck Complete NOTE: All component dimensions given in U.S. YTH22V42LS (96043011300), PRODUCT NO. 960 43 01-13 MOWER DECK KEY...