Owners Manual
Page 12
...If after cleaning, the drive wheels do not recommend sharpening blade - lbs. (47-54 Nm). Replace bent or damaged blades. Using a blade not approved by the manufacturer of blade adapter. Remove debris shield. NOTE: Remove the blade adapter and check the key inside hub of your mower is ... to work properly. Remove wheels from turning when removing blade bolt. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON BLADE ADAPTER. 4. Replace adapter if damaged. TIRES • Keep tires free of blade (opposite sharp edge) is 35-40 ft. are in...
...If after cleaning, the drive wheels do not recommend sharpening blade - lbs. (47-54 Nm). Replace bent or damaged blades. Using a blade not approved by the manufacturer of blade adapter. Remove debris shield. NOTE: Remove the blade adapter and check the key inside hub of your mower is ... to work properly. Remove wheels from turning when removing blade bolt. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON BLADE ADAPTER. 4. Replace adapter if damaged. TIRES • Keep tires free of blade (opposite sharp edge) is 35-40 ft. are in...
Owners Manual
Page 16
... Figs. 20 & 21) NOTE: Always use factory approved belt to spark plug. Reinstall rear gearcase pulley. 3. Be sure key in housing to blade adapter/ engine pulley. 5. Reattach spark plug wire to assure proper fit and long life. 1. Remove front belt keeper. 11. Remove rear gearcase pulley ... belt is 35-40 ft. Reinstall side bumper. 15. Place new belt on front gearcase pulley. 8. Route new belt through hole in blade adapter/engine pulley and crankshaft keyway are aligned; Reinstall front belt keeper. Reattach cable to input shaft (beneath pulley) and loosening pulley with a ...
... Figs. 20 & 21) NOTE: Always use factory approved belt to spark plug. Reinstall rear gearcase pulley. 3. Be sure key in housing to blade adapter/ engine pulley. 5. Reattach spark plug wire to assure proper fit and long life. 1. Remove front belt keeper. 11. Remove rear gearcase pulley ... belt is 35-40 ft. Reinstall side bumper. 15. Place new belt on front gearcase pulley. 8. Route new belt through hole in blade adapter/engine pulley and crankshaft keyway are aligned; Reinstall front belt keeper. Reattach cable to input shaft (beneath pulley) and loosening pulley with a ...
Owners Manual
Page 19
...Drive cable worn or broken. 4. Check/reinstall drive belt. 3. Out of pulley. 3. Bad spark plug. 6. Loose blade or broken blade adapter. 7. Tighten blade bolt or replace blade adapter. 8. Replace control bar. 10. Turn fuel valve lever to plug. 6. Engine flywheel brake is on pulleys / ...). 11. Disconnected battery connector (if equipped). 12. Raise cutting height. 2. Raise cutting height. 3. Check oil level. 6. Replace blade. Replace blade adapter. 4. not filling 2. Raise cutting height. 2. Empty fuel tank and refill tank with fresh, clean gasoline. 5. Connect wire to...
...Drive cable worn or broken. 4. Check/reinstall drive belt. 3. Out of pulley. 3. Bad spark plug. 6. Loose blade or broken blade adapter. 7. Tighten blade bolt or replace blade adapter. 8. Replace control bar. 10. Turn fuel valve lever to plug. 6. Engine flywheel brake is on pulleys / ...). 11. Disconnected battery connector (if equipped). 12. Raise cutting height. 2. Raise cutting height. 3. Check oil level. 6. Replace blade. Replace blade adapter. 4. not filling 2. Raise cutting height. 2. Empty fuel tank and refill tank with fresh, clean gasoline. 5. Connect wire to...
Owners Manual
Page 20
... model and serial number) to an authorized Servicing Dealer/Center for the applicable period of warranty service. 2015 www.husqvarna.com/us or www.husqvarna.com/ca 587 70 46-01 Rev. How to contact with your responsibility. To find your nearest authorized Servicing Dealer... varnish. E15, E25, E30, E50, E85), use ), including without limitation spark plugs, bulbs, filters, lubricants, starter cords, belts, blades, and blade adapters are not covered, nor is damage due to any defective product or part covered by use of gasoline containing more than an authorized servicing dealer...
... model and serial number) to an authorized Servicing Dealer/Center for the applicable period of warranty service. 2015 www.husqvarna.com/us or www.husqvarna.com/ca 587 70 46-01 Rev. How to contact with your responsibility. To find your nearest authorized Servicing Dealer... varnish. E15, E25, E30, E50, E85), use ), including without limitation spark plugs, bulbs, filters, lubricants, starter cords, belts, blades, and blade adapters are not covered, nor is damage due to any defective product or part covered by use of gasoline containing more than an authorized servicing dealer...
Parts List
Page 3
... be hazardous, damage your lawn mower and void your warranty. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. HUSQVARNA ROTARY LAWN MOWER - inches. 1 inch = 25.4 mm. NUMBER 96145002103) KEY PART NO. NO. 44 581 ... - 532 42 38-49 - - 115 72 19-32 - - 115 72 19-46 DESCRIPTION Kit, Lawn Mower Housing Rod, Hinge Blade Adapter / Pulley Blade, 22" Screw, Machine, Flanged Hex Head, with Nylon Patch, Grade 8, 3/8-24 x 1-1/8 Front Baffle Decal, Warning, Cut Finger Screw..., Dogpoint 3/8-16 x 1-1/8 Spring, Hinge Nut, Hex KEY PART NO. MODEL NUMBER HU800AWDH (MFG.
... be hazardous, damage your lawn mower and void your warranty. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. HUSQVARNA ROTARY LAWN MOWER - inches. 1 inch = 25.4 mm. NUMBER 96145002103) KEY PART NO. NO. 44 581 ... - 532 42 38-49 - - 115 72 19-32 - - 115 72 19-46 DESCRIPTION Kit, Lawn Mower Housing Rod, Hinge Blade Adapter / Pulley Blade, 22" Screw, Machine, Flanged Hex Head, with Nylon Patch, Grade 8, 3/8-24 x 1-1/8 Front Baffle Decal, Warning, Cut Finger Screw..., Dogpoint 3/8-16 x 1-1/8 Spring, Hinge Nut, Hex KEY PART NO. MODEL NUMBER HU800AWDH (MFG.