Hoover U6630900 - Self Propelled WindTunnel Bagless Upright Vacuum Support and Manuals
Get Help and Manuals for this Hoover item
View All Support Options Below
Free Hoover U6630900 manuals!
Problems with Hoover U6630900?
Ask a Question
Free Hoover U6630900 manuals!
Problems with Hoover U6630900?
Ask a Question
Popular Hoover U6630900 Manual Pages
Manual - Page 1
Self-Propelled WindTunnel™ Bagless with Powered Hand Tool by HOOVER
This product was designed for easy Assembly (See page 3)
www.hoover.com
Manual - Page 2
...Authorized Service 13 Cleaning Filters 8-9 Emptying Cup 7-9 Lubrication 13 Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand Tool Agitator Brush Roll 11-12 Replacing Edge Groomers . . . . .13 Replacing Headlight 9 Thermal Protector 13 Trouble Shooting 14 Clearing Blockages 14-15 Warranty 14
© 2001 The Hoover Company www.hoover...
Manual - Page 3
...
1 - 4
1-2
D
A
Looking at www.hoover.com to find the service outlet nearest you should happen to speak with owner's manual) E.
Remove switch lock (B) above the ON/OFF ...driver, tighten screws securely.
Cleaner body C. Handle screw packet (in order to move the hose in bag with a representative in the assembly of authorized service outlet locations (U.S.
Make sure all parts...
Manual - Page 4
...inside dirt cup) 14. Three-position handle
release pedal: step on pedal to lower handle to install the proper outlet. Auto brush roll indicator 19. Headlight 21. Cord hooks: wrap
cord around...Dirt FINDER' display 25. To move backward, gently pull handle back and guide the cleaner toward you have adjusted to correct setting for easy cord release. 27. The assembled cleaner will fit in rear...
Manual - Page 5
...only when the handle is first turned on .
For maximum cleaning performance, the following carpet height settings are removed.
After a few seconds, the red light will go off and the green light ...back of dirt is difficult to push, slide control to the next higher setting.
2 - 8
CD
Embedded Dirt FINDERTM feature (some models only)
With red and green lights (C), the 'Dirt FINDER' system ...
Manual - Page 6
...
When red is in the OFF window, brush roll is ROTATING. When red is in the ON window brush roll is STOPPED. Continue to top. Guide either side of nozzle parallel to the edge of the nozzle to remove dirt in moving the cleaner from clinging to another.
Before reaching edge...
Manual - Page 7
K. Crevice wand can also be used for cleaning stairs. To reattach, align hinges of the following parts: Lid (A) Dirt Cup (B) Pre-filter (C) HEPA Cartridge Filter(D) Dirt Inlet Opening (E)
While the cleaner is required, such as for extra reach with your cleaner.
3. Cleaning ...
Manual - Page 9
...down all the way, first ensure that no part of pre-filter screen extends above top edge of filter area. Remove any debris and replace shield, agitator and bottom plate (Figs. ...
3 - 1 7
Installing bulb
Pull old bulb straight out of the cleaner. Gently pull up and suction. Close door.
Using a screwdriver, remove the two screws as follows:
1. Headlight replacement
What to snap free if...
Manual - Page 10
... screw driver.
Remove the 4 screws as shown in direction shown.
3 - 2 2
Replacing bottom plate Reposition bottom plate and 4 Phillips head screws. Unplug cleaner when it is turned over large pulley (C) while rolling the pulley in Fig. 3-18. Replace belt if it is stretched, cut or broken. When purchasing a new belt, ask for HOOVER part No. 48414115...
Manual - Page 11
.... 3-18). Belt will "pop" into the rectangular slot (G) on brush roll.
3 - 2 7
H
G Powered hand tool
3 - 2 9
B
Agitator brush roll
replacement
When agitator brush roll brushes are worn, the brush roll should be replaced. Ask for HOOVER part No. 48414088.
3 - 2 8
A
Installing brush roll
Grasp brush roll and fit it so bottom faces up brush roll and slide V-belt...
Manual - Page 12
... of bottom plate into slots on front of brush roll into place. 5. Pivot bottom plate down , slide end plates (C) of tool. Replacing belt
When replacing belt, ask for HOOVER part No. 38528037. 1.
Replace brush roll, belt guard, and bottom plate as described in Figs. 3-28 through belt and position belt over gear teeth (D) on tool...
Manual - Page 13
...n . Do not add lubricant to replace
Disconnect cleaner from overheating. Thermal protector
An internal thermal protector has been designed into position as described in delay. Service
To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by the complete model number when requesting...
Manual - Page 14
... solution • Filter assembly not installed
properly • Remove filter assembly from spinning without affecting cleaning performance. Problem: Cleaning tools won 't turn
Possible...Problem: Cleaner hard to push
Possible cause Possible solution
• Incorrect carpet height setting • Move nozzle control knob to ON position
(carpet) • Flat belt broken or worn • Replace...
Manual - Page 15
B. C. Replace belt turbine, brush roll, belt guard and bottom plate. Appliances purchased elsewhere are questions concerning this appliance in correct operating condition during the warranted period. Hoover Factory Service Centers.
2.
While this warranty gives you specific legal rights, you may also have other rights which covers the cost of warranty service outlets, write or phone the...
Manual - Page 16
HOOVER y
son marcas registradas
HOOVER et
sont des marques déposées
HOOVER and
are registered trademarks
5-01 U6630-/45-/55-/70-900
Printed in Mexico
56511-B18
Hoover U6630900 Reviews
We have not received any reviews for Hoover yet.