Honeywell AQ1000TN2 - Low Voltage T-Stat Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell AQ1000TN2 manuals!
Problems with Honeywell AQ1000TN2?
Ask a Question
Free Honeywell AQ1000TN2 manuals!
Problems with Honeywell AQ1000TN2?
Ask a Question
Most Recent Honeywell AQ1000TN2 Questions
Popular Honeywell AQ1000TN2 Manual Pages
Owners Guide - Page 1
Hydronic Zoning Thermostat
AQ1000TN2
OWNER'S GUIDE
Place Bar Code Here
Owners Guide - Page 2
Need Help? Read and save these instructions.
® U.S. Patents pending. © 9-06 Honeywell International Inc.
For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502. Registered Trademark. All rights reserved.
69-2005EF
Owners Guide - Page 3
Table of contents
User's section About your new thermostat 1 Screen display ...2 Power-up / modes of operation 3 User's configuration menu 4 Temperature display and setting 6
Installer's section Installation...7 Configuration switches 8 Installer's configuration menu 9
Appendix Technical specifications 12 2-year limited warranty 13
69-2005EF
Owners Guide - Page 4
About your new thermostat
Honeywell's AQ1000TN2 hydronic zoning thermostat can choose among the following temperature control modes (see page 8):
A mode: • controls and displays the ambient air temperature
F mode: • controls and displays the ...
Owners Guide - Page 5
...)
Comfort / Unoccupied mode (see next page)
1 The outdoor temperature will be displayed only if the data is available. 2 This icon appears to indicate that the thermostat settings cannot be used to activate the backlight and to display the setpoint.
2
69-2005EF The backlight button and the buttons can still be modified as...
Owners Guide - Page 6
....
This value is set in the Installer's configuration menu (see page 5). Freeze Protection Mode
When the Freeze Protection mode is activated by the hydronic zoning controller, the thermostat is powered. Power-up / modes of operation:
Comfort Mode
The thermostat is normally in the Comfort mode.
This value is powered through the wires connecting it to...
Owners Guide - Page 7
.... To exit the menu, press the backlight button for 3 seconds to 9 °C)
Temporary
Temporary / Permanent
4
69-2005EF
Parameter Display mode Temperature setback Backlight
Default setting Options
Automatic
Automatic, °F, °C
7 °F (4 °C)
0 to 16 °F (0 to access the configuration menu. The first parameter is displayed.
2. To modify a parameter, press...
Owners Guide - Page 8
... respectively. Temperature Setback
When the Unoccupied mode is activated by the hydronic zoning controller (certain controller models only), the temperature setpoint is selected, the thermostat displays the temperature format set back).
When the automatic mode is lowered (set on the hydronic zoning controller. If °F or °C is pressed.
5
69-2005EF Backlight
Use this...
Owners Guide - Page 9
... temperature is displayed.
The measured temperature is below the thermostat's display range. Verify the thermostat and external (floor) sensor connections.
6
69-2005EF Temperature Display and Setting
The thermostat generally displays the actual (measured) temperature. Error Messages
The measured temperature is above the thermostat's display range. To change the setpoint, press one of...
Owners Guide - Page 10
Installation
1. see next page). 5. Insert the wires through the center hole of the faceplate up. Terminal
Description
1 TH 2 TH 3 SENSOR
4 SENSOR
AQ2000 Series hydronic zoning controller connections
External sensor connections for floor temperature measurement (required only if the thermostat is set to the base and secure with the captive screw.
Re-attach the faceplate to...
Owners Guide - Page 11
... AF mode should be used only when an external (floor) sensor is not used. Installer Configuration Menu (switch 2) Use DIP switch 2 to select the temperature control mode (A, F or AF).
Temperature Control Mode (switches 3 & 4) Use DIP switches 3 and 4 to set the thermostat in either Installer or User mode.
NOTE : DIP switch 1 is connected to the...
Owners Guide - Page 12
... be modified by the minimum and maximum setpoint temperatures. Return the thermostat to its initial position. To modify a parameter, press either of the thermostat in the up position (Installer mode). 3. To exit the menu, place switch 2 back to its base. 2.
Parameter
Default setting
Range
Minimum setpoint temperature
41 °F (5 °C)
41 °F (5 °C) to...
Owners Guide - Page 13
... temperature at the Freeze Protection temperature.
10
69-2005EF Freeze Protection Temperature This parameter is used to prevent frozen pipes inside the room where the thermostat is placed at which the thermostat can be set . When the Freeze Protection mode is activated by the hydronic zoning controller, the...
Owners Guide - Page 15
Technical Specifications
Power supply: powered by the boiler controller Default setpoint range: 40 °F to 100 °F (5 °C to 38 °C) Default floor limit (AF model): 40 °F to 100 °F (5 °C to 38 °...°C) Controller type: Proportional Integral (PI) Memory type: All settings are stored in non-volatile memory and are therefore safe during a power outage
12
69-2005EF
Owners Guide - Page 16
... will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to be to repair or replace the product within the terms stated above. This warranty shall not apply if it...
Honeywell AQ1000TN2 Reviews
We have not received any reviews for Honeywell yet.