Homelite UT10680 Support and Manuals
Get Help and Manuals for this Homelite item
View All Support Options Below
Free Homelite UT10680 manuals!
Problems with Homelite UT10680?
Ask a Question
Free Homelite UT10680 manuals!
Problems with Homelite UT10680?
Ask a Question
Most Recent Homelite UT10680 Questions
Ut10680a Chainsaw
Chain will not roate on bar. Break is off. What's the problem ?? Spindle rotates on bar & engine...
Chain will not roate on bar. Break is off. What's the problem ?? Spindle rotates on bar & engine...
(Posted by rwert 10 years ago)
Popular Homelite UT10680 Manual Pages
User Manual - Page 3
... retreat path from the falling tree.
Keep all instructions. Do not rely exclusively upon the safety devices built into the saw .
• Cut at high engine speeds. Fully
• Only use .
Do not operate a chain saw 's applications and limitations as well as the specific potential hazards related to heat stroke. Wear snug-fitting...
User Manual - Page 4
... you have a fire extinguisher available when using chain saw.
Use only the replacement guide bars and low kickback chains specified for the saw ; Do not leave the engine running . As an additional safety precaution, apply the chain brake prior to instruct other than the items listed in the instruction manual and all body parts
■ Always hold the flywheel...
User Manual - Page 5
...saw chain.
Never operate a chain saw that is damaged, improperly adjusted, or is a dangerous reaction that the saw .
Be sure that can cause circulatory problems in a container approved for general applications such as the size tree or workpiece involved.
English NOTE: The size of this manual... an authorized service center for added information on the guide bar to ...
User Manual - Page 8
... bar contacts any object such as a log or branch. Replacement Saw Chain A chain that complies with specific chain saws.
Low-Kickback Chain A chain that complies with other saws.
Rear Handle The support handle located at or toward the front of a chain saw and the guide bar, typically located close to stop the saw chain. It normally contains the throttle. It may not meet the...
User Manual - Page 16
... the STOP ( ) position. Wear all protective clothing and keep all parts of your body away from the chain/guide bar and muffler. Make adjustments with the unit supported on a stable surface so that the on/stop switch will not stop the saw on / stop switch repaired before storing. ADJUSTING IDLE SPEED
See Figure 14. WARNING:
The...
User Manual - Page 26
... adjusting pin may contain burrs. Without all the safety instructions in the direction of the bar. NOTE: When replacing the guide bar and chain, always use the specified bar and chain listed in the Bar and Chain Combinations section later in the STOP " " position before installing the guide bar, chain, clutch cover, and clutch drum.
Fig. 37
BAR GROOVE...
User Manual - Page 34
...supported on a stable surface so that the chain/guide bar does not contact the ground or any object. n Clean the air filter.
n Allow the engine to warm up prior to follow these instructions...
THE SAW CHAIN SHOULD NEVER TURN AT IDLE. English Use a brush or compressed air to the chain saw chain turning at least 50 ft. Do not allow bystanders close to keep all parts of this manual.
Idle...
User Manual - Page 37
... modified engines to the original factory specification before transporting or storing the unit. n Run the engine until it is inaccessible to children.
Page 37 -
Keep away from the product. n Drain all Federal and local regulations for oil. n Always place the scabbard over the guide bar and chain before operating below 2000 feet. English...
User Manual - Page 38
...not run proper- Contact an authorized service center for carburetor adjustment.
Refer to Spark Plug Replacement earlier in .
310627001
Chain Part Number 901212001 901212002 671258001
Drive Links 52 56 62
TROUBLESHOOTING
Problem
Possible Cause
Solution
Engine will not accelerate "L" (Low Jet)
properly. BAR AND CHAIN COMBINATIONS
Chain specifications: 3/8 in . pitch, .05 in . Engine...
User Manual - Page 39
...lubricant is not functioning. Engine starts and runs, but will not idle. Chain brake is too tight.
Tension chain per instructions in Adjusting the Chain Tension in the Maintenance section of this manual. Contact an authorized service center for a rebuild kit. TROUBLESHOOTING
Problem
Possible Cause
Solution
Engine starts, runs, Carburetor requires and accelerates adjustment...
User Manual - Page 40
... extends to all HOMELITE brand products manufactured by the dealer to the operating instructions as rental or commercial. Bump Knobs, Outer Spools, Cutting Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower Fans, Blower and Vacuum Tubes, Vacuum Bags and Straps, Guide Bars, Saw Chains, Blades
Homelite reserves the right...
User Manual - Page 41
... Protection Agency; If any such part (including any HOMELITE® Authorized Service Center for small non-road engines. Any such part repaired or replaced under warranty.
WWAARRRRAANNTTYY
THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS. EMISSIONS PARTS LIST
Emissions parts vary from the date the non...
User Manual 2 - Page 1
HOMELITE UT10548 / 14 in. 35cc CHAIN SAW UT10568 / 16 in. 38cc CHAIN SAW UT10588 / 18 in. 42cc CHAIN SAW
(ALL VERSIONS) REPAIR SHEET
User Manual 2 - Page 3
HOMELITE 35cc/38cc/42cc CHAIN SAWS MODEL NOs. UT10548, UT10568, UT10588
The model number will be found on a label attached to the engine housing. Always mention the model number in 1 988000561 Operator's Manual 3-22-11 (REV:02)
3
PARTS LIST (FIGURE A)
KEY PART NO. NUMBER
DESCRIPTION
QTY
1 310508011 Chain Cover Assembly 1 2 Guide Bar with SAFE-T-TIP: 310625001 UT10548 ...
Getting Started Guide - Page 1
...homelite.com and register your new tool on-line.
Go to RUN position. Note: 15-30
Allow the saw to run in
your new chain saw.
The clutch cover area must read and understand operator's manual... is not a substitute for chain saws to have bar and chain lubricant under the chassis after operating the saw. BAR
2
OIL
Add bar lubricant to oil tank.
3
O
Set ignition switch to RUN (I) ...
Homelite UT10680 Reviews
We have not received any reviews for Homelite yet.