Hitachi W6VB3SD - 2,600 RPM SUPERDRIVE Collated Screw System Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi W6VB3SD manuals!
Problems with Hitachi W6VB3SD?
Ask a Question
Free Hitachi W6VB3SD manuals!
Problems with Hitachi W6VB3SD?
Ask a Question
Popular Hitachi W6VB3SD Manual Pages
Instruction Manual - Page 3
... or machine damage are identified by WARNINGS on the power tool and in this Instruction Manual and in the sections which , if not avoided, may result in death or serious injury. Most accidents that has not been specifically recommended by HITACHI. Hazards that must be avoided by recognizing a potentially hazardous situation before operating or...
Instruction Manual - Page 5
... your model. Accessories that may become hazardous when used for one tool, may be used with another tool.
5. Follow instructions in a risk of injury. (2) When servicing a ... tools with care. Tools are recommended by qualified repair personnel. Be sure switch is designed. (3) Do not use only identical replacement parts. Always wear eye protection. Keep cutting tools sharp...
Instruction Manual - Page 6
... used until repaired. 12. Prolonged exposure to youself or others. don't use a power tool for cutting tree limbs or logs. 8. Prevent potential injuries to high intensity noise can lead to the instructions provided herein. Apply the screw driver body perpendicularly to do the job of the tool "live" and shock the operator.
2. English
SPECIFIC SAFETY...
Instruction Manual - Page 7
...out.
15. Operate the power tool at all times. Do not wipe plastic parts with such solvents. NEVER leave tool running unattended. Turn power off .
14... using it may damage and crack plastic parts. Do not wipe them with solvent. hertz A ... watt ... Check for repairs by a Hitachi authorized service center.
16. Wipe plastic parts with a soft cloth lightly dampened with ...
Instruction Manual - Page 8
... follow these precautions: ⅜ Only Hitachi Authorized Service Center should disassemble or assemble this
power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in this power tool, HITACHI has adopted a double insulation design. SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO...
Instruction Manual - Page 9
... • W8VB2
SPECIFICATIONS
Model
W6VM W6V4 W6VA4 W6VB3 W8VB2
Motor
Single-Phase, Series Commutator Motor
Power Source
Single-Phase, 120 V 60 Hz
Current
6.5 A
No-Load Speed
0-6000/min. 0-4500/min. 0-3000/min. 0-2600/min. 0-1700/min. English
FUNCTIONAL DESCRIPTION
NOTE: The information contained in this manual.
Some illustrations in this Instruction Manual may show details...
Instruction Manual - Page 11
... the rear side) when the reversing switch lever is set to the "L" side position, the bit rotates counterclockwise and can be used to loosen and remove screws. Confirm the direction of the motor will result.
7. CAUTION: Never change the bit rotating direction while operating the Screw Driver. R side
Lever
Fig. 2
Sub
Locator
Stopper (B)
Gear cover
Fig...
Instruction Manual - Page 12
... which the trigger switch is set to the "R" side position. To facilitate continuous operation, pull the trigger switch and depress the switch stopper. The switch will be fully transferred to the screw head groove, and push the Screw Driver against the screw. CAUTION Never change the direction of hex-socket (or bit holder) rotation.
12 Turn...
Instruction Manual - Page 13
... manner of hex-head socket and remove
Fig. 7
the bit holder, then pull out the bit with pliers. 4. Mounting the hex-socket or the bit Install the bit in the reverse order to tighten the Self-drilling screw into a steel plate, cut material stuck in the magnet bit will prevent the bushing from receptacle to switch power...
Instruction Manual - Page 14
... inspection of the motor The motor unit winding is noticed.
2. socket (bit) with soapy water.
5. socket (bit) will be performed by a Hitachi Authorized Service Center. WARNING: Using this tool should ONLY be used, all screws and ensure that only authorized replacement parts will damage screw heads, replace the hex. Service and repairs All quality power tools will be carried out by...
Instruction Manual - Page 15
...94 mm)) (Code No. 317671 1
15 The use Only authorized HITACHI replacement parts and
accessories. code numbers and/or design) may be changed without any obligation on the part of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
STANDARD ACCESSORIES
(1) No. 2 Phillips driver bit (Code No. 971511Z 1 (2) Magnetic bit holder (Code No. 982554Z...
Instruction Manual - Page 16
...
Sub-Stopper
Sub-Stopper (G) (Code No. 323352)
Sub-Stopper (F) (Code No. 323351)
NOTE: Specifications are subject to change without any obligation on the part of the HITACHI.
16 H 1/4
985328
H 5/16
985327
H 3/8
985326
Size H 1/4 H 5/16 H 3/8
2. H 1/4
985332
H 5/16
985322
H 3/8
985330
Non magnetic type
Size
Code No. For other screws
Screw head
Type
Bit
Size
No.1 No.2 No.3
No...
Parts List - Page 1
...FEEDTRACK
2
725428
FEED TRACK HEX SOCKET SCREW
1/4"-20 x 7.4mm
5
725426
FEED TRACK
1
725432
TUBE FOR END PLATE
1
DEPTH ADJUSTMENT PARTS
QTY
725472
DEPTH CONTROL RETAINER
1
725474
DEPTH CONTROL SPRING
1
725473
DEPTH CONTROL ADJUSTMENT
WHEEL
1
725475
SNAP E RING E2
1
EXTENSION PARTS
QTY
725476
EXTENSION 19"
1
729430
BIT EXTENSION
1
729431
HANDLE ASSEMBLY
1 725413...
Operating Instructions - Page 1
... E RING E2
1
EXTENSION PARTS
QTY
725476
EXTENSION 19"
1
729430
BIT EXTENSION
1
729431
HANDLE ASSEMBLY
1
Call 1-800-706-7337 or your sales rep. IMPORTANT!
Adjust the nosepiece so there is in driving position in the center of its tools or fasteners for replacement parts.
Operating Instructions
For SuperDrive 75 Series
OPERATION
1. Insert a strip of screws into the index...
Operating Instructions - Page 2
... leaves both hands free to install a polarized outlet. Follow instructions for replacement parts. Use only authorized parts. Lift the tool enough to relieve all times. 13. Fine tune screw depth by loosening the screws and pushing in any way.
6. What causes mis-drives? 1. Nose piece screw is worn and must call 1-800706-7337 for replacement parts. Nose piece is skipped...
Hitachi W6VB3SD Reviews
We have not received any reviews for Hitachi yet.