Specifications
Page 6
... life and usage condition 29 6.3.5 Preventive maintenance 29 6.3.6 Load/unload ...29 6.4 Mechanical specifications...31 6.4.1 Physical dimensions and weight 31 6.4.2 Mounting hole locations 32 6.4.3 Connector and jumper description 32 6.4.4 Mounting orientation ...33 6.4.5 Load/unload mechanism 33 6.5 Vibration and shock ...33 6.5.1 Operating vibration ...33 6.5.2 Nonoperating vibration 34 6.5.3 Operating shock ...34 6.5.4 Nonoperating shock ...35...
... life and usage condition 29 6.3.5 Preventive maintenance 29 6.3.6 Load/unload ...29 6.4 Mechanical specifications...31 6.4.1 Physical dimensions and weight 31 6.4.2 Mounting hole locations 32 6.4.3 Connector and jumper description 32 6.4.4 Mounting orientation ...33 6.4.5 Load/unload mechanism 33 6.5 Vibration and shock ...33 6.5.1 Operating vibration ...33 6.5.2 Nonoperating vibration 34 6.5.3 Operating shock ...34 6.5.4 Nonoperating shock ...35...
Specifications
Page 42
Travelstar 80GN Hard Disk Drive Specification 32 6.4.2 Mounting hole locations The mounting hole locations and size of the drive are included in Section 7.10, "Drive address setting" on page 39. Figure 2: Mounting hole locations 6.4.3 Connector and jumper description A jumper is described in Section 7.2, "Interface connector" on page 55. Connector specifications are shown below. The jumper setting method is used to designate the drive address as either master or slave.
Travelstar 80GN Hard Disk Drive Specification 32 6.4.2 Mounting hole locations The mounting hole locations and size of the drive are included in Section 7.10, "Drive address setting" on page 39. Figure 2: Mounting hole locations 6.4.3 Connector and jumper description A jumper is described in Section 7.2, "Interface connector" on page 55. Connector specifications are shown below. The jumper setting method is used to designate the drive address as either master or slave.
Specifications
Page 46
... jumper information if required by the customer. 6.8 Electromagnetic compatibility When installed in accordance with ISO 7779 at each octave band 6.7 Identification labels The following formula only when determining compliance. The EC marking for the certification appears on user request. Travelstar 80GN Hard Disk Drive Specification... assembly containing the statement "Made by Hitachi" or equivalent, part number, EC number, and FRU number. • A bar code label which is placed on the disk drive based on the drive. 6.8.2 C-TICK mark The drive complies with the Australian EMC standard "...
... jumper information if required by the customer. 6.8 Electromagnetic compatibility When installed in accordance with ISO 7779 at each octave band 6.7 Identification labels The following formula only when determining compliance. The EC marking for the certification appears on user request. Travelstar 80GN Hard Disk Drive Specification... assembly containing the statement "Made by Hitachi" or equivalent, part number, EC number, and FRU number. • A bar code label which is placed on the disk drive based on the drive. 6.8.2 C-TICK mark The drive complies with the Australian EMC standard "...
Specifications
Page 52
signal shall be unable to determine the drive address (master or slave) when the jumper on the interface connector is at the falling edge of ...to close the respective position of the first valid command by device 1 to indicate to Travelstar 80GN Hard Disk Drive Specification 42 or DIOW- The DASP- If DASP- shall be asserted by an Open-Drain...that device 1 has passed its reset procedure and is ready (DRDY=1). The signal level of a valid Execute Drive Diagnostics command for drive 1 to 00h. resistor. Device 0 shall allow up to assert DASP-. This line is driven low at ...
signal shall be unable to determine the drive address (master or slave) when the jumper on the interface connector is at the falling edge of ...to close the respective position of the first valid command by device 1 to indicate to Travelstar 80GN Hard Disk Drive Specification 42 or DIOW- The DASP- If DASP- shall be asserted by an Open-Drain...that device 1 has passed its reset procedure and is ready (DRDY=1). The signal level of a valid Execute Drive Diagnostics command for drive 1 to 00h. resistor. Device 0 shall allow up to assert DASP-. This line is driven low at ...
Specifications
Page 65
... shown below. When the drive address is a Master. Travelstar 80GN Hard Disk Drive Specification 55 If pin 28 is ground (or low), the drive is Cable Select, the address depends on the interface connector determines the drive address. Two addresses require the setting of the AT interface cable. 7.10 Drive address setting A jumper placed on the condition of...
... shown below. When the drive address is a Master. Travelstar 80GN Hard Disk Drive Specification 55 If pin 28 is ground (or low), the drive is Cable Select, the address depends on the interface connector determines the drive address. Two addresses require the setting of the AT interface cable. 7.10 Drive address setting A jumper placed on the condition of...
Specifications
Page 126
...page 118. Travelstar 80GN Hard Disk Drive Specification 116 below ViL 12- 8 Device 1 hardware reset result Device 0 clear these bits to 0 12(=0) Reserved 11(=X) 1=Device 1 passed diagnostic 10-9(=X) How Device 1 determined the device number: 00= Reserved 01= a jumper was used...0 detected Device 1 4(=X) 1=Device 1 passed diagnostic 3(=X) 1=Device 0 passed diagnostic 2-1(=X) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method used or method unknown 8(=1) Always 7- 0 Device 0 hardware reset result Device ...
...page 118. Travelstar 80GN Hard Disk Drive Specification 116 below ViL 12- 8 Device 1 hardware reset result Device 0 clear these bits to 0 12(=0) Reserved 11(=X) 1=Device 1 passed diagnostic 10-9(=X) How Device 1 determined the device number: 00= Reserved 01= a jumper was used...0 detected Device 1 4(=X) 1=Device 1 passed diagnostic 3(=X) 1=Device 0 passed diagnostic 2-1(=X) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method used or method unknown 8(=1) Always 7- 0 Device 0 hardware reset result Device ...