Specifications
Page 42
Connector specifications are shown below. Travelstar 80GN Hard Disk Drive Specification 32 The jumper setting method is used to designate the drive address as either master or slave. Figure 2: Mounting hole locations 6.4.3 Connector and jumper description A jumper is described in Section 7.2, "Interface connector" on page 55. 6.4.2 Mounting hole locations The mounting hole locations and size of the drive are included in Section 7.10, "Drive address setting" on page 39.
Connector specifications are shown below. Travelstar 80GN Hard Disk Drive Specification 32 The jumper setting method is used to designate the drive address as either master or slave. Figure 2: Mounting hole locations 6.4.3 Connector and jumper description A jumper is described in Section 7.2, "Interface connector" on page 55. 6.4.2 Mounting hole locations The mounting hole locations and size of the drive are included in Section 7.10, "Drive address setting" on page 39.
Specifications
Page 46
... standard"Limits and methods of measurement of radio disturbance characteristics of the head disk assembly containing the statement "Made by Hitachi" or equivalent, part number, EC number, and FRU number. • A bar code label which is to ...drive model number, serial number, place of manufacture, and UL/ CSA logos. • Labels containing jumper information if required by half a revolution 6.6.2 Discrete tone penalty Discrete tone penalties are affixed to the A-weighted sound power (Lw) with EC directive 89/336/EEC. The location on user request. Travelstar 80GN Hard Disk Drive...
... standard"Limits and methods of measurement of radio disturbance characteristics of the head disk assembly containing the statement "Made by Hitachi" or equivalent, part number, EC number, and FRU number. • A bar code label which is to ...drive model number, serial number, place of manufacture, and UL/ CSA logos. • Labels containing jumper information if required by half a revolution 6.6.2 Discrete tone penalty Discrete tone penalties are affixed to the A-weighted sound power (Lw) with EC directive 89/336/EEC. The location on user request. Travelstar 80GN Hard Disk Drive...
Specifications
Page 52
... DIOR- If the host connects to assert PDIAG-. Following a Power On Reset, software reset, or RESET-, drive 1 shall negate PDIAG- If device 1 is ready to Travelstar 80GN Hard Disk Drive Specification 42 is ready to 00h. was not asserted by device 1 within 30 seconds to indicate that device ...signal level detected on the interface connector is pulled up to determine the drive address (master or slave) when the jumper on the interface for any purpose, the host shall ensure that a drive is active. Drive 1 shall then assert PDIAG- The signal level of the first valid ...
... DIOR- If the host connects to assert PDIAG-. Following a Power On Reset, software reset, or RESET-, drive 1 shall negate PDIAG- If device 1 is ready to Travelstar 80GN Hard Disk Drive Specification 42 is ready to 00h. was not asserted by device 1 within 30 seconds to indicate that device ...signal level detected on the interface connector is pulled up to determine the drive address (master or slave) when the jumper on the interface for any purpose, the host shall ensure that a drive is active. Drive 1 shall then assert PDIAG- The signal level of the first valid ...
Specifications
Page 65
...below. Travelstar 80GN Hard Disk Drive Specification 55 Two addresses require the setting of the AT interface cable. If pin 28 is open (or logic high), the drive is a Master. If pin 28 is ground (or low), the drive is a Slave. When the drive address ... connector determines the drive address. When pin C is grounded, the drive does not spin up at shipment is Setting 1 (no jumper). 7.10 Drive address setting A jumper placed on the condition of pin 28 of a jumper. 31 42 1 2 3 4 5 Figure 3: Drive address setting Setting 1-Device 0 (Master) (no jumper is used) Setting...
...below. Travelstar 80GN Hard Disk Drive Specification 55 Two addresses require the setting of the AT interface cable. If pin 28 is open (or logic high), the drive is a Master. If pin 28 is ground (or low), the drive is a Slave. When the drive address ... connector determines the drive address. When pin C is grounded, the drive does not spin up at shipment is Setting 1 (no jumper). 7.10 Drive address setting A jumper placed on the condition of pin 28 of a jumper. 31 42 1 2 3 4 5 Figure 3: Drive address setting Setting 1-Device 0 (Master) (no jumper is used) Setting...
Specifications
Page 126
...6(=X) 1=Semi-duplex mode is enabled 5(=X) 1=Device 0 detected Device 1 4(=X) 1=Device 1 passed diagnostic 3(=X) 1=Device 0 passed diagnostic 2-1(=X) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method used or method unknown 8(=1) Always 7- 0 Device 0 hardware reset result Device 1 clears these bits... XXXXH 80XXH 0000H Description Current Advanced Power Management level 15- 8(=40h) Reserved 7- 0(=xxh) Current Advanced Power Management level set by model." Travelstar 80GN Hard Disk Drive Specification 116
...6(=X) 1=Semi-duplex mode is enabled 5(=X) 1=Device 0 detected Device 1 4(=X) 1=Device 1 passed diagnostic 3(=X) 1=Device 0 passed diagnostic 2-1(=X) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method used or method unknown 8(=1) Always 7- 0 Device 0 hardware reset result Device 1 clears these bits... XXXXH 80XXH 0000H Description Current Advanced Power Management level 15- 8(=40h) Reserved 7- 0(=xxh) Current Advanced Power Management level set by model." Travelstar 80GN Hard Disk Drive Specification 116