Specifications
Page 30
Mounting hole locations 6.4.3 Connector and jumper description A jumper is described in section 7.2, "Interface connector" on page 58. Model Height (mm) 160 GB, 120 GB models 9.5±0.2 80 GB, 60 GB, 40 GB models 9.5±0.2 Table 15. Weight (gram) 102 Max 95 Max Figure 2. Physical ... of the drive are included in section 7.10, "Drive address setting" on page 41. 30/188 The jumper setting method is used to designate the drive address as either master or slave. Connector specifications are shown below. Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.4 ...
Mounting hole locations 6.4.3 Connector and jumper description A jumper is described in section 7.2, "Interface connector" on page 58. Model Height (mm) 160 GB, 120 GB models 9.5±0.2 80 GB, 60 GB, 40 GB models 9.5±0.2 Table 15. Weight (gram) 102 Max 95 Max Figure 2. Physical ... of the drive are included in section 7.10, "Drive address setting" on page 41. 30/188 The jumper setting method is used to designate the drive address as either master or slave. Connector specifications are shown below. Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.4 ...
Specifications
Page 35
The presence of labels containing jumper information depends on the customer. 6.8 Electromagnetic compatibility When installed in the drawing provided by HITACHI" or equivalent, part number, EC number, and FRU number. Labels containing the vendor's name, disk drive model number, serial number...based technically on the top of Hitachi products EU EMC Directive, Technical Requirements and Conformity Assessment Procedures 6.8.1 CE Mark The product is certified for the certification appears on user request. Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.7 Identification labels The ...
The presence of labels containing jumper information depends on the customer. 6.8 Electromagnetic compatibility When installed in the drawing provided by HITACHI" or equivalent, part number, EC number, and FRU number. Labels containing the vendor's name, disk drive model number, serial number...based technically on the top of Hitachi products EU EMC Directive, Technical Requirements and Conformity Assessment Procedures 6.8.1 CE Mark The product is certified for the certification appears on user request. Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.7 Identification labels The ...
Specifications
Page 40
... ms to indicate to 5 Volt through a 10 kΩ resistor. 40/188 Following the receipt of a valid Execute Drive Diagnostics command for drive 1 to determine the drive address (master or slave) when the jumper on the same AT interface cable to post status. It is an indication to provide status. IORDY This signal is recommended... Power There are tied together within 1 ms (to indicate to device 0 that device 1 has passed its reset procedure and is the "+5 V Motor" input pin. Travelstar 5K160 (PATA) Hard Disk Drive Specification Following a Power On Reset, software reset, or RESET...
... ms to indicate to 5 Volt through a 10 kΩ resistor. 40/188 Following the receipt of a valid Execute Drive Diagnostics command for drive 1 to determine the drive address (master or slave) when the jumper on the same AT interface cable to post status. It is an indication to provide status. IORDY This signal is recommended... Power There are tied together within 1 ms (to indicate to device 0 that device 1 has passed its reset procedure and is the "+5 V Motor" input pin. Travelstar 5K160 (PATA) Hard Disk Drive Specification Following a Power On Reset, software reset, or RESET...
Specifications
Page 53
... Travelstar 5K160 (PATA) Hard Disk Drive Specification Drive address setting A jumper placed on the condition of pin 28 of jumper at shipment is grounded, the drive does not spin up at POR. When the drive address is a Master. If pin 28 is ground (or low), the drive is Cable Select, the address depends on the interface connector determines the drive...
... Travelstar 5K160 (PATA) Hard Disk Drive Specification Drive address setting A jumper placed on the condition of pin 28 of jumper at shipment is grounded, the drive does not spin up at POR. When the drive address is a Master. If pin 28 is ground (or low), the drive is Cable Select, the address depends on the interface connector determines the drive...
Specifications
Page 110
Travelstar 5K160 (PATA) Hard Disk Drive Specification 93 xxxxH Hardware reset result 15-13 Device detected result 15 (=0) Reserved 14 (=1) Always 13 (=x) 1=Device detected CBLID- PIO 105-106 0000H...7 (=0) Reserved 6 (=x) 1=Semi-duplex mode is enabled 5 (=x) 1=Device 0 detected Device 1 4 (=x) 1=Device 1 passed diagnostic 3 (=x) 1=Device 0 passed diagnostic 2-1 (=x) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method was used or the method is unknown 0 (=1) Always 94 80xxH Automatic Acoustic Management...
Travelstar 5K160 (PATA) Hard Disk Drive Specification 93 xxxxH Hardware reset result 15-13 Device detected result 15 (=0) Reserved 14 (=1) Always 13 (=x) 1=Device detected CBLID- PIO 105-106 0000H...7 (=0) Reserved 6 (=x) 1=Semi-duplex mode is enabled 5 (=x) 1=Device 0 detected Device 1 4 (=x) 1=Device 1 passed diagnostic 3 (=x) 1=Device 0 passed diagnostic 2-1 (=x) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method was used or the method is unknown 0 (=1) Always 94 80xxH Automatic Acoustic Management...