Specifications
Page 30
..." on page 58. Connector specifications are shown below. Model Height (mm) 160 GB, 120 GB models 9.5±0.2 80 GB, 60 GB, 40 GB models 9.5±0.2 Table 15. The jumper setting method is used to designate the drive address as either master or slave. Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.4 Mechanical specifications 6.4.1 Physical dimensions and weight The following figure lists the...
..." on page 58. Connector specifications are shown below. Model Height (mm) 160 GB, 120 GB models 9.5±0.2 80 GB, 60 GB, 40 GB models 9.5±0.2 Table 15. The jumper setting method is used to designate the drive address as either master or slave. Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.4 Mechanical specifications 6.4.1 Physical dimensions and weight The following figure lists the...
Specifications
Page 35
... standard. Labels containing the vendor's name, disk drive model number, serial number, place of labels containing jumper information depends on CISPR22:1993-12 measurement standards and limits. The EC marking for certification of Hitachi products EU EMC Directive, Technical Requirements and Conformity ... provided by HITACHI" or equivalent, part number, EC number, and FRU number. MIC standards are likewise based on user request. The location on the disk drive is placed on the disk drive based on IEC standards. 35/188 Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.7...
... standard. Labels containing the vendor's name, disk drive model number, serial number, place of labels containing jumper information depends on CISPR22:1993-12 measurement standards and limits. The EC marking for certification of Hitachi products EU EMC Directive, Technical Requirements and Conformity ... provided by HITACHI" or equivalent, part number, EC number, and FRU number. MIC standards are likewise based on user request. The location on the disk drive is placed on the disk drive based on IEC standards. 35/188 Travelstar 5K160 (PATA) Hard Disk Drive Specification 6.7...
Specifications
Page 40
...) when the jumper on the same AT interface cable to or from the receipt of the cable connector in order to indicate that device 1 has passed its drive diagnostics. CSEL (Cable Select) This signal is monitored to GND through a 15 kΩ resistor with DMACK-. or DIOW- Travelstar 5K160 (PATA) Hard Disk Drive Specification Following a Power...
...) when the jumper on the same AT interface cable to or from the receipt of the cable connector in order to indicate that device 1 has passed its drive diagnostics. CSEL (Cable Select) This signal is monitored to GND through a 15 kΩ resistor with DMACK-. or DIOW- Travelstar 5K160 (PATA) Hard Disk Drive Specification Following a Power...
Specifications
Page 53
7.10 Travelstar 5K160 (PATA) Hard Disk Drive Specification Drive address setting A jumper placed on the condition of pin 28 of jumper at POR. When the drive address is Cable Select, the address depends on the interface connector determines the drive address. If pin 28 is open (or logic high), the drive is Setting 1: no jumper is used) Setting 2-Device 1 (Slave) Setting...
7.10 Travelstar 5K160 (PATA) Hard Disk Drive Specification Drive address setting A jumper placed on the condition of pin 28 of jumper at POR. When the drive address is Cable Select, the address depends on the interface connector determines the drive address. If pin 28 is open (or logic high), the drive is Setting 1: no jumper is used) Setting 2-Device 1 (Slave) Setting...
Specifications
Page 110
... 0 detected Device 1 4 (=x) 1=Device 1 passed diagnostic 3 (=x) 1=Device 0 passed diagnostic 2-1 (=x) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method was used or the method is unknown 0 (=1) Always 94 80xxH Automatic Acoustic Management...models for Number of those parameters that are vendor specific. below ViL 12-8 Device 1 hardware reset result. Travelstar 5K160 (PATA) Hard Disk Drive Specification 93 xxxxH Hardware reset result 15-13 Device detected result 15 (=0) Reserved 14 (=1) Always 13 (=x) ...
... 0 detected Device 1 4 (=x) 1=Device 1 passed diagnostic 3 (=x) 1=Device 0 passed diagnostic 2-1 (=x) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method was used or the method is unknown 0 (=1) Always 94 80xxH Automatic Acoustic Management...models for Number of those parameters that are vendor specific. below ViL 12-8 Device 1 hardware reset result. Travelstar 5K160 (PATA) Hard Disk Drive Specification 93 xxxxH Hardware reset result 15-13 Device detected result 15 (=0) Reserved 14 (=1) Always 13 (=x) ...