Specifications
Page 6
...Specification ...53 7.1 Jumper settings 53 7.1.1 Jumper pin location 53 7.1.2 Jumper pin identification 53 7.1.3 Jumper pin assignment 54 7.1.4 Jumper positions 54 7.2... Environment 58 7.2.1 Temperature and humidity 58 7.2.2 Corrosion test 59 7.3 DC power requirements 59 7.3.1 Input voltage 59 7.3.2 Power supply current (typical 60 7.3.3 Power supply generated ripple at drive...Mounting hole locations 63 7.5.3 Connector locations 63 7.5.4 Drive mounting 64 7.5.5 Heads unload and actuator lock ...
...Specification ...53 7.1 Jumper settings 53 7.1.1 Jumper pin location 53 7.1.2 Jumper pin identification 53 7.1.3 Jumper pin assignment 54 7.1.4 Jumper positions 54 7.2... Environment 58 7.2.1 Temperature and humidity 58 7.2.2 Corrosion test 59 7.3 DC power requirements 59 7.3.1 Input voltage 59 7.3.2 Power supply current (typical 60 7.3.3 Power supply generated ripple at drive...Mounting hole locations 63 7.5.3 Connector locations 63 7.5.4 Drive mounting 64 7.5.5 Heads unload and actuator lock ...
Specifications
Page 58
... RSV I GECA HFDB DS CS/SP GND RSV 7.1.4 Jumper positions 7.1.4.1 16 logical head default (normal use ) • 15 logical head default • 32 GB clip • Power up in standby Within each of these four jumper settings the pin assignment selects Device 0, Device 1, Cable Selection,...D B IGECA HFDB IGECA HFDB IGECA HFDB IGECA H F D B DEVICE 0 (Master) DEVICE 1 (Slave) CABLE SEL DEVICE 1 (Slave) Present Shipping Default Condition (DEVICE 0) Deskstar 7K80 Hard Disk Drive Specification 54 7.1.3 Jumper pin assignment There are four jumper settings as shown in the following figures.
... RSV I GECA HFDB DS CS/SP GND RSV 7.1.4 Jumper positions 7.1.4.1 16 logical head default (normal use ) • 15 logical head default • 32 GB clip • Power up in standby Within each of these four jumper settings the pin assignment selects Device 0, Device 1, Cable Selection,...D B IGECA HFDB IGECA HFDB IGECA HFDB IGECA H F D B DEVICE 0 (Master) DEVICE 1 (Slave) CABLE SEL DEVICE 1 (Slave) Present Shipping Default Condition (DEVICE 0) Deskstar 7K80 Hard Disk Drive Specification 54 7.1.3 Jumper pin assignment There are four jumper settings as shown in the following figures.
Specifications
Page 59
...A-B or C-D position does not affect any selection of Device or Cable Selection mode. In CSEL mode, installing or removing the jumper blocks at E-F. Deskstar 7K80 Hard Disk Drive Specification 55 IGECA HFDB IGECA HFDB IGECA HFDB IGECA HFDB DEVICE 0 (Master) DEVICE 1 (Slave) CABLE SEL DEVICE 1 (... mode) the jumper block must be installed at a high level, the drive address is the Device 0 position. 7.1.4.2 15 logical head default The figure below shows the jumper positions used to select Device 0, Device 1, Cable Selection, or Device1 (Slave) Present setting 15 logical heads...
...A-B or C-D position does not affect any selection of Device or Cable Selection mode. In CSEL mode, installing or removing the jumper blocks at E-F. Deskstar 7K80 Hard Disk Drive Specification 55 IGECA HFDB IGECA HFDB IGECA HFDB IGECA HFDB DEVICE 0 (Master) DEVICE 1 (Slave) CABLE SEL DEVICE 1 (... mode) the jumper block must be installed at a high level, the drive address is the Device 0 position. 7.1.4.2 15 logical head default The figure below shows the jumper positions used to select Device 0, Device 1, Cable Selection, or Device1 (Slave) Present setting 15 logical heads...
Specifications
Page 60
...: Jumper settings for Disabling Auto Spin I GECA HFDB DEVICE 0 (Master) I GECA HFDB DEVICE 1 (Slave) I GECA HFDB CABLE SEL I G E C A H F D B DEVICE 0 (Master) DEVICE 1 (Slave) CABLE SEL DEVICE 1 (Slave) Present Note: The jumper setting acts as a 32GB clip which clips the LBA to 32 GB for capacity clip to 32GB I G E C A H F D B I G E C A H F D B I G E C A H F D B I GECA HFDB DEVICE 1 (Slave) Present Deskstar 7K80 Hard Disk Drive Specification...
...: Jumper settings for Disabling Auto Spin I GECA HFDB DEVICE 0 (Master) I GECA HFDB DEVICE 1 (Slave) I GECA HFDB CABLE SEL I G E C A H F D B DEVICE 0 (Master) DEVICE 1 (Slave) CABLE SEL DEVICE 1 (Slave) Present Note: The jumper setting acts as a 32GB clip which clips the LBA to 32 GB for capacity clip to 32GB I G E C A H F D B I G E C A H F D B I G E C A H F D B I GECA HFDB DEVICE 1 (Slave) Present Deskstar 7K80 Hard Disk Drive Specification...
Specifications
Page 61
To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at a high level, the drive address is 1 (Device 1). Deskstar 7K80 Hard Disk Drive Specification 57 These jumper settings are used for limiting power supply current when multiple drives are used. 2. In the CSEL mode the drive address is determined by AT interface signal #28 CSEL as...
To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at a high level, the drive address is 1 (Device 1). Deskstar 7K80 Hard Disk Drive Specification 57 These jumper settings are used for limiting power supply current when multiple drives are used. 2. In the CSEL mode the drive address is determined by AT interface signal #28 CSEL as...
Specifications
Page 105
... the states as a result of a jumper. A device needs a SET FEATURES subcommand to spin-up to active state when the device has powered up into active state Deskstar 7K80 Hard Disk Drive Specification 101 If power-up into Standby, the device shall set shall not be enabled and disabled via ...the SET FEATURES command. The device remains in Standby until the SET FEATURES subcommand is enabled or disabled •...
... the states as a result of a jumper. A device needs a SET FEATURES subcommand to spin-up to active state when the device has powered up into active state Deskstar 7K80 Hard Disk Drive Specification 101 If power-up into Standby, the device shall set shall not be enabled and disabled via ...the SET FEATURES command. The device remains in Standby until the SET FEATURES subcommand is enabled or disabled •...
Specifications
Page 145
Deskstar 7K80 Hard Disk Drive Specification 141 detection. 1=detect 0=not detect 3 Device diag. 1=pass 0=fail 2-1 How to determine the device number 00=Reserved. 01=Jumper. 10=CSEL signal. 11=Some other method. 8 Shall be set to one if Dev 1. 7-0 Device 0 H/W reset result 7 Reserved 6 Respond for Enhanced ...result. 12 Reserved 11 PDIAG-asertion. 1=assert 0=not assert 10-9 How to determine the device number: 00=Reserved. 01=Jumper. 10=the CSEL signal. 11=some other method. 0 Shall be set to one if Dev 0. detection. 1=detect 0=not detect 4 PDIAG-
Deskstar 7K80 Hard Disk Drive Specification 141 detection. 1=detect 0=not detect 3 Device diag. 1=pass 0=fail 2-1 How to determine the device number 00=Reserved. 01=Jumper. 10=CSEL signal. 11=Some other method. 8 Shall be set to one if Dev 1. 7-0 Device 0 H/W reset result 7 Reserved 6 Respond for Enhanced ...result. 12 Reserved 11 PDIAG-asertion. 1=assert 0=not assert 10-9 How to determine the device number: 00=Reserved. 01=Jumper. 10=the CSEL signal. 11=some other method. 0 Shall be set to one if Dev 0. detection. 1=detect 0=not detect 4 PDIAG-