HP Indigo WS6600 Specifications

Indigo Technical Tips and Workarounds

Page 50
... the correction, press linearity correction. Instructions a. plug-in operating instructions System: HP Indigo WS6600 Digital Press - VR configuration (software v. 8.9.i4) 1. b. Background N/A 3. Activate the correction for specific substrates only where a linearity issue arises. Double-click the desktop shortcut to deactivate the patch after the specific substrate had been used. c. plug-in operating instructions Remember to open...

Indigo Technical Tips and Workarounds

Page 53
Replace the Air flow Corona Suction sensor. 4. Purpose To describe how to the specifications in the HP Indigo WS6600 Digital Press Site Preparation Guide (CA394-08582). Part Numbers N/A Air flow Corona suction error 49 Background N/A 3. Instructions Verify that a suction unit is installed, and if so, verify that it is operating according to correct an Air flow Corona Suction sensor error. 2. 26 Air flow Corona suction error System: HP Indigo WS6600 Digital Press 1.

Deinstalling Indigo 6X00 Series Digital Presses

Page 78
... in its original box without any foam. Secure the boxes on all small parts Follow these steps to pack all small parts. 1. There are no specific guidelines for packing the Show KIT because the separate parts are already packed in a box. 2. Packing steps of the Show KIT Follow these steps to...

Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00

Page 40
.... Turn off the UPS and wait 1 minute for preliminary procedures. 1. DO NOT put your hands inside any of the units while the press is within specifications (Refer to the relevant Site Preparation Guide): ● Required ambient temperature 20 to 25° C (68 to 77° F) ● Required ambient relative humidity 50...

Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00

Page 60
Figure 3-37 Air flow arrow on the Anemometer For the specifications see Anemometer AVM-01/03 specs on page 62. In Systab Editor, set IO_PDB_EXIT_BLANKET_SUCTION to measure the EBV and IRS suction air flow. 1. Figure 3-38 ...

Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00

Page 63
... for dripping correction procedures when the press in Ready (print) status, touch Main Menu > Press status > System status, and verify that temperature values are within specifications. In Systab Editor, set IO_COOLER_FAN to 10000. 2. 1. With the press in ready status. 1. In Systab Editor, IO_Outlet_Temperature_Sensor, the value should be in the middle of...

Electrometer Board Test

Page 15
... UC door and release the E-Stop button. See step 4 on page 6 for reference. 21. End of Board Test If results of electrometer board are within specification, then board is in order, but problem remains, check the probe as follows: End of Board Test 13 IMPORTANT: Take precaution when disconnecting and connecting...

Electrometer Board Test

Page 27
.... Immerse the probe into IPA and agitate (stir) the probe. 4. End of Probe Test If results of Probe Test 25 End of probe are within specification, then probe is functioning properly. ● If not, try cleaning the probe. ● If cleaning the probe did not help, replace the probe.

Rewinder Calibration

Page 3
The default parameters for the rewinder may not be appropriate for the specific substrate. Overview 1 1 Overview An overview of Rewinder Calibration. The procedure below describes how to calibrate the rewinder for high-sensitivity film substrates. When encountering problems with blocking or ink back-transfer on the finishing line, it is necessary to calibrate the rewinder.

Baseline procedure -- CA393-03500 Rev 04

Page 5
... it in the OFF position. 3. Check the cleaning station unit. DO NOT put your hands inside any of the units while the press is within specifications (Refer to the relevant Site Preparation Guide): ● Required ambient temperature 20 to 25° C (68 to 77° F) ● Required ambient relative humidity 50...

Baseline procedure -- CA393-03500 Rev 04

Page 25
...; 2 m/sec. Verify that the EBV air knife, and upper and lower suctions are connected firmly. 3. Figure 2-37 Air flow arrow on the Anemometer For the specifications see Anemometer AVM-01/03 specs on page 28. Measuring the external heater hood blower fan outlet air flow 23 Figure 2-38 External heater hood...

Baseline procedure -- CA393-03500 Rev 04

Page 28
... status. 1. Figure 2-43 Utility cabinet outlet Press in Ready (print) status, touch Main Menu > Press status > System status, and verify that temperature values are within specifications.

Baseline procedure -- CA393-03500 Rev 04

Page 30
A Appendix Anemometer AVM-01/03 specs Features and specification of AVM-01/03 specs. 28 Appendix A Appendix

Working with Indigo ElectroInk Invisible Yellow and Blue for Indigo WS6600 WS6800 and 6900 Digital PressesHow-to Guide

Page 5
... two new inks, invisible to use the correct ink file for the relevant ink. This is intended for HP Indigo WS6600 Digital Press and up (i.e., including HP Indigo WS6800, 6r, and 6900 Digital Presses). ● Press software version 15.0 i34 or higher. ●...● Surprising graphics as a gloss difference. Limitations of the HP Indigo ElectroInk Invisible Yellow and Blue It explains the limitations of the HP Indigo ElectroInk Invisible Yellow and Blue. ● Visibility (under indoors conditions, to specifically fit brand protection and security printing applications. Not invisible on ...

Splice Detection System Installation and Troubleshooting -- CA393-10241 Rev 00

Page 37
... it counts down towards 0 while the web is moving forward. The calibration signal is set low for each calibration attempt. The signal stays high until a specific web distance has passed the sensor (local FP drive parameter c_TeachDistance_mm% = 2000 mm). Direct digital input 24 VDC drive FP terminal 27; #19.34 = 0 (signal...

Working with Indigo ElectroInk SilverHow-to Guide

Page 5
... to match the appearance of applications, such as labels, shrink sleeves, and food packaging (with no contact with food), either as a solid graphic or as specific software features. HP Indigo ElectroInk Silver was developed to ensure the Silver solution full performance. Who can benefit from reading this document to Guide? P/N C8Q13A, which...

Working with Indigo ElectroInk SilverHow-to Guide

Page 6
...with Silver, a low background appearance is not supported. Printing HP Indigo ElectroInk Silver as solid color. Spot refinement - See below a list of metallic colors has not been fully tested, therefore HP does not guarantee a specific performance. ● When using an M0 external spectrophotometer, it... the ElectroInk Silver optical density (OD) directly. A specific calibration is not possible to Installing the dedicated BID base and developer roller on page 31. ● The following are the limitations for working with HP Indigo ElectroInk Silver. ● "BID memory" effect - ...

Working with Indigo ElectroInk SilverHow-to Guide

Page 7
● When using HP Indigo ElectroInk Silver, it is highly recommended to carefully test jobs before first time production, including labeling or lamination (in flexible packaging). ● Results depend mainly on the design of background in frame-overlap areas. A specific calibration is available to ... ElectroInk Silver). ● It is recommended to disable the automatic color calibration feature, as part of ElectroInk Silver. ● HP Indigo ElectroInk Silver is visually stable, therefore it is more visible in jobs where there is not necessary / not recommended to calibrate the...

Working with Indigo ElectroInk SilverHow-to Guide

Page 22
Manual adjustments to prevent / reduce background in the overlap area between silver hits. IMPORTANT: Manual overlap adjustments are done for the specific job, and are recommended for "fine tuning" when the automatic mode (see Manual overlap adjustments on page 18. The "overlap ... correct the mode during print, although the window is possible to other jobs. 18 Chapter 4 Working with HP Indigo ElectroInk Silver Once the "overlap prevention" option is selected for any specific job, under its Job Properties - For the overlap prevention to work properly, printing is possible only in...

HP Indigo WS6600 Specifications

Related Manual Pages

Indigo Technical Tips and Workarounds

Indigo Technical Tips and Workarounds

Deinstalling Indigo 6X00 Series Digital Presses

Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00

Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00

Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00

Electrometer Board Test

Electrometer Board Test

Rewinder Calibration

Baseline procedure -- CA393-03500 Rev 04

Baseline procedure -- CA393-03500 Rev 04

Baseline procedure -- CA393-03500 Rev 04

Baseline procedure -- CA393-03500 Rev 04

Working with Indigo ElectroInk Invisible Yellow and Blue for Indigo WS6600 WS6800 and 6900 Digital PressesHow-to Guide

Splice Detection System Installation and Troubleshooting -- CA393-10241 Rev 00

Working with Indigo ElectroInk SilverHow-to Guide

Working with Indigo ElectroInk SilverHow-to Guide

Working with Indigo ElectroInk SilverHow-to Guide

Working with Indigo ElectroInk SilverHow-to Guide

Similar Questions

Related Terms

Ask a New Question

Manuals / Documents

Related Items

Points & Prizes

HP Manuals

HP Reviews

Contact Information

Scoreboard Ratings

HP Recalls