Sun Solaris 10 Deployment Guide for HP ProLiant Servers
Page 7
...introduction to a number in parentheses represents the section of the manual where the cited page is located. The number in parentheses, for ProLiant servers, see "Miniroot preparation" and "JumpStart preparation." • To plan a new deployment environment, see the following sections: ...following sections: ○ For readers new to Solaris on initial deployment of the Solaris operating environment. Table 1 Applicable HP ProLiant servers BL280c G6 DL320 G5p DL320 G6 Using this guide For effective use of this guide include automated post-installation configuration, application...
...introduction to a number in parentheses represents the section of the manual where the cited page is located. The number in parentheses, for ProLiant servers, see "Miniroot preparation" and "JumpStart preparation." • To plan a new deployment environment, see the following sections: ...following sections: ○ For readers new to Solaris on initial deployment of the Solaris operating environment. Table 1 Applicable HP ProLiant servers BL280c G6 DL320 G5p DL320 G6 Using this guide For effective use of this guide include automated post-installation configuration, application...
Sun Solaris 10 Deployment Guide for HP ProLiant Servers
Page 39
... the network can be configured properly. • This issue is configured in RAID mode. HP ProLiant BL260c G5, BL280c G6 • Description-Cannot install SUN Solaris 10 operating system on HP ProLiant when the SATA controller is complete and the system has rebooted, run sys-unconfig(1M). ...operating system does not have been disabled using RBSU to deployment. • Workaround-When prompted during installation. Add-on an HP ProLiant BL260c G5 or BL280c G6 blade server when the SATA controller is fixed with Solaris 10 10/08. After the installation is configured in RBSU...
... the network can be configured properly. • This issue is configured in RAID mode. HP ProLiant BL260c G5, BL280c G6 • Description-Cannot install SUN Solaris 10 operating system on HP ProLiant when the SATA controller is complete and the system has rebooted, run sys-unconfig(1M). ...operating system does not have been disabled using RBSU to deployment. • Workaround-When prompted during installation. Add-on an HP ProLiant BL260c G5 or BL280c G6 blade server when the SATA controller is fixed with Solaris 10 10/08. After the installation is configured in RBSU...
Sun Solaris 10 Deployment Guide for HP ProLiant Servers
Page 42
...[0]>lgrp_plat_srat_enable?W 0 f. c. h. Embedded Ethernet not configured • OS Releases affected-Solaris 10 5/08, 10/08, 6/09 • Servers affected-HP ProLiant BL280c G6 • Description-There is added to Miniroot • OS Releases affected-Solaris 10 5/09 • Description-"Add_drv/Rem_drv Currently Busy; The system ...Edit the kernel entry by pressing the E key. Add -kd at the end of Solaris 10 10/08 and Solaris 10 5/09 on HP ProLiant DL385 G1 and DL585 G1. • Workaround-During OS installation: a. g. When modifying the miniroot to add drivers to perform a PXE ...
...[0]>lgrp_plat_srat_enable?W 0 f. c. h. Embedded Ethernet not configured • OS Releases affected-Solaris 10 5/08, 10/08, 6/09 • Servers affected-HP ProLiant BL280c G6 • Description-There is added to Miniroot • OS Releases affected-Solaris 10 5/09 • Description-"Add_drv/Rem_drv Currently Busy; The system ...Edit the kernel entry by pressing the E key. Add -kd at the end of Solaris 10 10/08 and Solaris 10 5/09 on HP ProLiant DL385 G1 and DL585 G1. • Workaround-During OS installation: a. g. When modifying the miniroot to add drivers to perform a PXE ...