Heat Pump Installation Manual
Page 7
...operation • High (590PSI) and low (80PSI) refrigerant pressure switches monitoring extreme operation • Compressor sound blanket • Corrosion resistant evaporator fins Models Voltage/Phase/Hz 100 240/1/60 TABLE 2: SPECIFICATIONS 112 120 H/C 240/1/60 240/1/60 125 240/1/60 Power Input (kW) 80A-80RH-80W ...2" 10.25 590 360 615 R410A A1 245 245 285 285 37 37 36.5 x 31 x 42 36.5 x 31 x 42 Outdoor Use USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 140 240/1/60 208-230/3/60 7.2 34.5 32.1/2.4/34.5 185/4.3/189.3 42.5 50 70 140000 5.7 130000 5.5 85000 4 58.5 280 320...
...operation • High (590PSI) and low (80PSI) refrigerant pressure switches monitoring extreme operation • Compressor sound blanket • Corrosion resistant evaporator fins Models Voltage/Phase/Hz 100 240/1/60 TABLE 2: SPECIFICATIONS 112 120 H/C 240/1/60 240/1/60 125 240/1/60 Power Input (kW) 80A-80RH-80W ...2" 10.25 590 360 615 R410A A1 245 245 285 285 37 37 36.5 x 31 x 42 36.5 x 31 x 42 Outdoor Use USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 140 240/1/60 208-230/3/60 7.2 34.5 32.1/2.4/34.5 185/4.3/189.3 42.5 50 70 140000 5.7 130000 5.5 85000 4 58.5 280 320...
Heat Pump Installation Manual
Page 16
...remote relay to ensure that the pool heater is 200 feet. Note: The unit must be "On" to starting the heater. 15 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS This enables the normal operation mode and the heater will operate in heating. Use 20 AWG wire for runs less than 30... relay (J28) is needed, it turns on the control board. 2. As water conditioning is closed , the heater will shut off connections). 1. Heat/Cool models connect the heating remote relay to terminal J7 and cooling remote relay to the local set point control at the heater, press and hold both...
...remote relay to ensure that the pool heater is 200 feet. Note: The unit must be "On" to starting the heater. 15 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS This enables the normal operation mode and the heater will operate in heating. Use 20 AWG wire for runs less than 30... relay (J28) is needed, it turns on the control board. 2. As water conditioning is closed , the heater will shut off connections). 1. Heat/Cool models connect the heating remote relay to terminal J7 and cooling remote relay to the local set point control at the heater, press and hold both...
Heat Pump Installation Manual
Page 17
... temperature. POOL - REMOTE OPERATION - The arrows will respond to maintain the water temperature setting for AUTO. Control Setup Heat/Cool Models This pool heater is discharged from the Compressor (E) and flows into a high temperature, high pressure superheated vapor, which mode is currently... active. 16 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS The heater will stop heater operation to protect the unit in Figure 16a to maintain the water temperature setting for...
... temperature. POOL - REMOTE OPERATION - The arrows will respond to maintain the water temperature setting for AUTO. Control Setup Heat/Cool Models This pool heater is discharged from the Compressor (E) and flows into a high temperature, high pressure superheated vapor, which mode is currently... active. 16 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS The heater will stop heater operation to protect the unit in Figure 16a to maintain the water temperature setting for...