Hayward CAT 6000 Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward CAT 6000 manuals!
Problems with Hayward CAT 6000?
Ask a Question
Free Hayward CAT 6000 manuals!
Problems with Hayward CAT 6000?
Ask a Question
Most Recent Hayward CAT 6000 Questions
Chlorine Sensor
hi we already have replaced the chlorine sensor but it still shows the error.
hi we already have replaced the chlorine sensor but it still shows the error.
(Posted by Arlanaledia 1 year ago)
Popular Hayward CAT 6000 Manual Pages
CAT 6000 Owners Manual - Page 1
... RevA_draft10
CAT 6000®
Water Quality Controller
Owner's Manual
\
Contents
Introduction 2
Installation 4
Pool Chemistry 14
System Operation 15
System Maintenance 29
Network Communications 30
Troubleshooting 34
Warranty 38
CAT-6000
Hayward Pool Products 620 Division Street, Elizabeth NJ 07207
Phone (908)-355-7995 www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
CAT 6000 Owners Manual - Page 3
... or service requests through a wireless network to the POOLCOMM web server for outbound notification via email, cell phone or PDA. Monthly charges apply. The results include elimination of "human error", accurate and reliable maintenance of the components incorporated in a typical CAT 6000 wireless water quality control system:
2 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS The CAT 6000 controller...
CAT 6000 Owners Manual - Page 6
...receive power.
5
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Ensure the mounting bracket is ...controller unit which will meet the following criteria:
A. C.
Away from pool or spa. Securely attach the Mounting Plate to a vertical wall according to pool or spa operator. The install location should have enough space to be within reach of the assembly.
3. Remove three (3) screws to support...
CAT 6000 Owners Manual - Page 16
...the status icon bar at the top of the pool or spa. CAT Controllers recommends establishing desired pH, sanitizer residual, calcium hardness, total alkalinity, temperature and cyanuric acid levels prior to initiating automated control of the unit.
15 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Always maintain water chemistry according to manufacturer's recommendations. This bar indicates any...
CAT 6000 Owners Manual - Page 18
..., displayed parameters, output configurations, and other options can be entered. The default password is "0000". Normal Operating Mode
During normal operating mode, the display will indicate sensed pH, ORP, free chlorine, temperature, and TDS.
17 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS The CAT 6000 menu provides access to all necessary controls, setup information, and specifications.
CAT 6000 Owners Manual - Page 21
...HAYWARD GENUINE REPLACEMENT PARTS surement is necessary to match manual water testing results, compensate for an aging or unclean pH sensor, and confirm proper operation of cyanuric acid use with a factory default setting... control method. • Push the OK button to switch to 30 minutes. Change The pH Setpoint
The CAT 6000 is useful when servicing pH feed equipment, or if pH chemical ...
CAT 6000 Owners Manual - Page 22
....
Select Chlorine Feed Mode
The CAT 6000 is programmed with a factory default setting to save the setpoint. Before chlorine calibration, ensure that the chlorine sensor is displayed.
21
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Change The Chlorine Setpoint
The CAT 6000 is programmed with a factory default setpoint of ORP=650 mV. CAT Controllers considers this to save the setpoint...
CAT 6000 Owners Manual - Page 23
...in the pH set point, TDS set point, or cyanuric acid level. Calibrate NaCl (Salt)
The CAT 6000 requires NaCl calibration ...HAYWARD GENUINE REPLACEMENT PARTS Before NaCl calibration, it is displayed. • Use the Up and Down buttons to enter the total alkalinity of the water as measured by a
test kit.
• Push the OK button to enter the selected value. Enter Total Alkalinity
The CAT 6000...
CAT 6000 Owners Manual - Page 24
... HAYWARD GENUINE REPLACEMENT PARTS Transmit Statistics
The CAT 6000 can be sent to select Request. • Push the OK button, the controller will check for a display to be enabled or disabled:
• From the menu, select the Display option using the Enter button. • Use the Up and Down buttons to select which display is to set...
CAT 6000 Owners Manual - Page 30
... replace teflon thread-seal tape, and reinstall sensors. specific ...HAYWARD GENUINE REPLACEMENT PARTS Sensor Maintenance
The sensors must be protected from the flow cell.
System Maintenance
CAT 6000 Controller Package
The CAT 6000 controller unit is important to maintain total alkalinity on bather load and other facility- Cleaning of sensors should be performed using a quality manual...
CAT 6000 Owners Manual - Page 31
... install it and press the transmit data button.
The flow cell and poly tubing must first register an account. Although the CAT 6000 controller is subject to storing or transporting the CAT 6000 controller unit. Place the CAT 6000 unit where you need assistance. Before these units can also be generated. Controller Storage
The controller unit is designed to your first CAT 6000...
CAT 6000 Owners Manual - Page 33
... your username and password, then click on a facility name to www.poolcomm.com. Click on Login. At the Login screen type your communicating units:
Status Symbol The status symbol indicates the 24 hour alarm status of facilities automated with CAT 6000 wireless controllers. Alarm time delays for facility.
32 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Using The...
CAT 6000 Owners Manual - Page 35
..., check the Overfeed timeout setting as cloudy water, inefficient use of sanitizer and bather discomfort. First check the chemical level. Troubleshooting
pH Out Of Range
pH is below 7.0 is considered acidic and above 7.8 will cause corrosive water resulting in the tank. If the manual test does not agree with the controller clean the sensor.
This...
CAT 6000 Owners Manual - Page 36
...generates a service request alarm.
35
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Service Request
The Transmit Statistics button on the CAT 6000 sends logged data to prevent the controller from continuing to keep up with chemical ...maximum feed time and has not reached its set point. chlorine oxidizers. First, check the chemical supply and chemical feeder. The proper ORP range for swimming ...
CAT 6000 Owners Manual - Page 40
... from the CAT 6000 controller. pH should be calibrated. Initial calibration of the sensor may require daily calibrations until the discoloration is 48 hours for which the sensor needs to be made near the desired set point level of the Chlorine for instructions on the platinum sensor wire as DPD. See the CAT 6000 operations manual for the...
Hayward CAT 6000 Reviews
We have not received any reviews for Hayward yet.