Harbor Freight Tools 66615 - 7 in. Electronic Polisher/Sander Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 66615 manuals!
Problems with Harbor Freight Tools 66615?
Ask a Question
Free Harbor Freight Tools 66615 manuals!
Problems with Harbor Freight Tools 66615?
Ask a Question
Popular Harbor Freight Tools 66615 Manual Pages
User Manual - Page 4
... all instructions listed below may create a hazard and cause personal injury.
3. Do not use the power tool if the switch does not turn it on and off are caused by a qualified repair person using only identical replacement parts. Damaged accessories will run the power tool at least equal to your power tool serviced by poorly...
User Manual - Page 5
...replacement.
18. Prepare to filter out microscopic particles. (California Health & Safety Code ...instructions discussed in a well ventilated area, and work before use accessories that may make exposed metal parts...instruction manual cannot cover all possible conditions and situations that require liquid coolants. SAFETY
SETUP... practical ways to secure and support the workpiece to a complete ...
User Manual - Page 7
...problems are not being caused or worsened from use.
Anyone using vibrating tools regularly or for an extended period should not use this manual...immediately. Grip tool as lightly as possible.
2.
SETUP
OPERATION
MAINTENANcE
Item 66615
For technical questions, please ...Do not smoke during use. Page 7 SAVE THESE INSTRUcTIONS. To reduce the risk of it). To reduce vibration...
User Manual - Page 8
...codes and ordinances. The plug and outlet should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the plug. Do not use . If the plug will not fit the outlet, have it repaired...Standard Association, and the National Electrical Code.
2.
If damaged, have a proper outlet installed by a service facility before use the tool if ...
User Manual - Page 9
...replace a damaged extension cord or have it repaired by a qualified electrician before set... Insulated
Canadian Standards Association
Underwriters Laboratories, Inc. Read the manual before using more than one tool, add the nameplate amperes...Current
A
Amperes
n0 xxxx/min. Keep flammable objects away. SAFETY
SETUP
Extension cords
1. Grounded tools require a three wire extension cord. As...
User Manual - Page 10
SAFETY
Specifications
Electrical Specifications 120 VAC / 60 Hz / 10 A
No load speed
1000~3500 RPM
Maximum Accessory Size 7″ Diameter
Mounting Disc Type
7″ Hook & Loop
Variable Speed Switch Sliding Button (+ & -)
Display Unit of Measure RPM x 100
Accessories
7″ Hook & Loop
Backing Pad
225428
SETUP
OPERATION
MAINTENANcE
Page 10
For technical questions, please ...
User Manual - Page 11
SAFETY
Setup - Then release pressure on either side of the tool. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram... Turn the Power Switch off and unplug the Polisher from its electrical outlet before set up or use of this manual including all text under subheadings therein before assembling or making any adjustments to the ...
User Manual - Page 12
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use personal ... SANDING DISc (54)
Figure B
POLISHING BONNET (52)
Workpiece and Work Area Set Up
1. Tool Set Up
SAFETY
SETUP
TO PREVENT SERIOUS INJURY FROM AccIDENTAL OPERATION: Make sure that will vary according to ...
User Manual - Page 13
...flat against the surface of the vehicle. Note: The most common error when waxing/polishing a vehicle is held firmly against the surface, ...tool to come to -reach areas of the Foam Pad. SAFETY
SETUP
NOTIcE: Only use , too much wax in subsequent applications.
Keep... Foam Pad, apply wax to any hard-to a complete stop before setting it out of wax. Clean, then store the tool indoors out of...
User Manual - Page 14
...stop before setting it down... pattern up and down . Replace worn sanding discs as needed.
9. SETUP
OPERATION
MAINTENANcE
Page 14
For ...technical questions, please call 1-888-866-5797. Unplug the tool. Allow the tool to start the tool.
5.
Wipe the work .
7. Clean, then store the tool indoors out of children's reach. SAFETY
Sanding Instructions...
User Manual - Page 15
SAFETY
SETUP
OPERATION
MAINTENANcE
Item 66615
For technical questions, please call 1-888-866-5797. PLEASE READ THE FOLLOWING cAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
Page 15 IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD...
User Manual - Page 16
... the problem corrected before performing any other condition that the Power Switch is damaged, it must be performed only by a qualified service technician....Servicing
Procedures not specifically explained in this manual must be replaced only by a qualified technician.
AFTER USE, wipe external surfaces of moving parts, • damaged cord/electrical wiring, • cracked or broken parts...
User Manual - Page 17
... cord is tight.
2. Have technician service tool. 1. diameter extension cord. Have qualified technician replace brushes. Have technician service tool. Motor being reduced by long ... SETUP
OPERATION
MAINTENANcE
Item 66615
For technical questions, please call 1-888-866-5797.
Accessory damaged, worn or wrong type for example.)
Overheating.
1. SAFETY
Troubleshooting
Problem
Tool...
User Manual - Page 18
... no serial number, record month and year of purchase instead. Item 66615
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SAFETY
SETUP
Parts List and Diagram
Parts List
Part
Description
Qty
Part
Description
Qty
1
Screw
5
30 Bracket
1
2
Right Handle
1
31 Front Bearing
1
4
Circuit Board
1
32 Gear...
User Manual - Page 19
SAFETY
SETUP
Assembly Diagram
34
33
35 32
31 30
36
37
29
38
40
28
39
41
42
43
44
45 46
47 48
26 25 24
49
23 22
27 19 18 17 16 15
14
50 51
10 11
9 8
1
13
2
12
4
52
7
6
Foam Bonnet (53) not shown. Sanding Disc (54) not shown.
(See Figure A, page 9.)
5
OPERATION
MAINTENANcE
Item 66615
For technical questions, please call 1-888-866-5797. Page 19
Harbor Freight Tools 66615 Reviews
We have not received any reviews for Harbor Freight Tools yet.