Harbor Freight Tools 60244 - 1/8in. Air Micro Die Grinder Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 60244 manuals!
Problems with Harbor Freight Tools 60244?
Ask a Question
Free Harbor Freight Tools 60244 manuals!
Problems with Harbor Freight Tools 60244?
Ask a Question
Popular Harbor Freight Tools 60244 Manual Pages
User Manual - Page 2
... bystanders, children, and visitors away while operating the tool.
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
WARNING -
Addresses practices not related to result in the ignition of Contents
Safetye 2 Specifications 6 Setup 7 Operationa 10
Maintenancei 12 Parts List and Diagram 14 Warranty 16
Safety...
User Manual - Page 3
... or another practical way to secure and support the workpiece to a rotating part of the tool increases the risk of drugs...
a hard hat must be repaired.
4. There is a risk of binding and is off .
Safety
Setup
Personal Safety
1. Do not wear...Maintain the tool with the specific tool model, increases the risk of starting . Disconnect the tool from moving parts, breakage of the tool...
User Manual - Page 4
...replacement parts. Such gases are capable of the tool or serious injury to persons. WARNING marking concerning Risk of Respiratory Injury. Tool service...Injury. Symbols and Specific Safety Instructions
Symbol Definitions
Symbol
Property... tool or specified by qualified repair personnel.
2. WARNING marking concerning... air-pressure range.
2.
When servicing a tool, use oxygen, carbon...
User Manual - Page 5
...Install an in-line shutoff valve to filter out microscopic particles. (California Health & Safety Code...problems are : • Lead from lead-based paints • Crystalline silica from use . Anyone using vibrating tools regularly or for the forces generated may occur. Let the tool do this manual... stop . Safety
Setup
Specific Safety Instructions
1. Moving parts can grab the ...
User Manual - Page 6
Excess air pressure is hazardous and may cause the tool to exceed stated rated speed.
Safety
Setup
Functional Description
Specifications
Maximum Air Pressure Air Inlet Rated Speed* Average Air Consumption Collet Size
90 PSI 1/4"-18 NPT 56,000 RPM 2 CFM @ 90 PSI 1/8"
* Rated speed at ...
User Manual - Page 7
...section for best service, as shown on... prevent accidental operation. Repair any other bottled gas...Setup
Initial Tool Set Up/Assembly
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up . Note: For additional information regarding the parts...FROM ACCIDENTAL OPERATION: Do not install a female quick coupler on...
User Manual - Page 8
...
Operation
Maintenance
Page 8
Figure B: Portable Air Supply Setup
Lubricated Tools
BC D
A
E
F
A
For technical questions, please call 1-800-444-3353. Non-lubricated Tools
C
EH
BG
A
Description
A Air Hose B Filter C Regulator D Lubricator (optional) E Coupler and ...
User Manual - Page 9
Figure C: Stationary Air Supply Setup
Item 60244
For technical questions, please call 1-800-444-3353.
Slope
Lubricated
G
Tools
C
J
K
H
L
M
F
CD E
I
IN
B A
B A
F
C
J
F
Non-lubricated Tools
LO H
Description
A Vibration... release Increases coupler life Prevents water vapor from damaging workpiece For fine tuning airflow at tool
Maintenance
Operation
Setup
Safety
Page 9
User Manual - Page 10
...set up during use , looking for damaged, loose, and missing parts. Safety
Setup
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at least the maximum speed of the Die Grinder.
3.
Friction will present a hazard while working. Slide the shaft of this manual... or pets to heat up or use tool until repaired.
This tool does not have a safety guard. Route...
User Manual - Page 11
... to the maximum air pressure rating of the regulator up to start the tool.
4. Setup
Operation
Maintenance
Item 60244
For technical questions, please call 1-800-444-3353. Page 11 ...the accessory to decrease speed.
5. If an automatic oiler is variable.
Safety
General Operating Instructions
1. Hold tool clear and slowly turn the switch to the airline connection before use ....
User Manual - Page 12
...instructions. Setup
Operation
Maintenance
Page 12
For technical questions, please call 1-800-444-3353.
Cleaning, Maintenance, and Lubrication
Note: These procedures are in this manual...of moving parts
• cracked or broken parts
• any inspection, maintenance, or cleaning procedures.
Safety
User‑Maintenance Instructions
Procedures not specifically explained in...
User Manual - Page 13
... and tight.
5.
Safety
Troubleshooting
Problem
Possible Causes
Likely Solutions
Decreased output. 1. Cross‑threaded housing
(Slight air leakage components. Replace all safety precautions whenever diagnosing or servicing the tool. If housing cannot tighten properly, internal parts may be misaligned. Tighten housing assembly. Setup
Operation
Maintenance
Item 60244...
User Manual - Page 14
...
1
Setup
Operation
Maintenance
Record Product's Serial Number Here:...Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL...REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 60244 Note: Some parts...
User Manual - Page 15
Page 15
Assembly Diagram
Safety
Setup
Operation
Maintenance
Item 60244
For technical questions, please call 1-800-444-3353.
User Manual - Page 16
...This warranty gives you specific legal rights and you ...date of returning the product. We will either repair or replace the product at our expense, but if ...installation, normal wear and tear, or to the original purchaser that its products meet high quality and durability standards, and warrants to lack of our product. makes every effort to assure that this warranty, the product or part...
Harbor Freight Tools 60244 Reviews
We have not received any reviews for Harbor Freight Tools yet.