Harbor Freight Tools 35570 - 1/2 HP Mortising Machine Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
This item is in your list!
View All Support Options Below
Free Harbor Freight Tools 35570 manuals!
Problems with Harbor Freight Tools 35570?
Ask a Question
Free Harbor Freight Tools 35570 manuals!
Problems with Harbor Freight Tools 35570?
Ask a Question
Popular Harbor Freight Tools 35570 Manual Pages
User Manual - Page 1
...; 1996 by Harbor Freight Tools®. For technical questions or replacement parts, please call 1-800-444-3353.
No portion of this manual may be reproduced in serious injury. Diagrams within this manual or any artwork contained herein may not be included.
MORTISING MACHINE
MODEL 35570
Visit our website at: http://www.harborfreight.com
Read this...
User Manual - Page 2
... AREA CONDITIONS. KEEP CHILDREN AWAY. USE THE RIGHT TOOL. DRESS PROPERLY. Use a full face mask as the mortising machine will need this manual for the safety instructions, assembly instructions, operating procedures, parts list, and diagram. Do not yank it to reduce the risk of fire, electric shock, and personal injury. SECURE WORK. It's safer...
User Manual - Page 3
...parts, mounting, and other conditions that it comes to be in the instruction manual. Keep tool clean and bits and chisels sharp to determine if your judgment or reflexes are tired. 18. Have defective switches replaced by an authorizer1 service... the equipment is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in proper...
User Manual - Page 4
...and pieces required for any loose, frayed or exposed wires, damaged insulation, or defective connections, replace the cord. EXTENSION CORDS
Since your tool has a grounded, three-prong plug, you may ..., preferable listed by its AWG (American Wire Gauge) rating; The extension cord must meet this manual, or on indoor use, you must be no complications. The amps of the cord(s). Handle ...
User Manual - Page 5
Tighten the set screw (19...chuck key(47). 3. Page 5
SKU 35570 Bracket A (4) 4. Chuck Key (47)
ASSEMBLY INSTRUCTIONS
1. The handle's end should be removed. 6. NOTE: If you must clamp the machine down ...flammable solvent, clean the rust inhibitor from the base (3), guide column (16), gear column, gear casing(23), and all other required parts. 4. Four Screws (40, for bracket A) 5. Three ...
User Manual - Page 6
...in a couple of the chisel, then tighten the chuck. Make sure the chisel's slot is accomplished. Set the depth stop (18) at a time. 4.
Do not mortise holes deeper than 1/2" can be ... Tighten the busing screw, and replace the left to be accomplished simply by moving the wood for proper chip ejection. 6. Slide the bit into the chuck. Set the fence (9) so that it ...
User Manual - Page 7
... chisels are accessible through the panel on the outside face of the chisel will replace a bit three times as often as irregular grooves or hollows) the bit must be ... the inner edge of the spur and the cutting edge of use , lubricate the both columns with a light machine oil. Set the RPM's very low or the temper of the chisel.
It is sharpenable, however, if there is dull, it in ...
User Manual - Page 8
Problem :LOOQRWVWDUW
0DFKLQHVWDUWV EXWELWGRHV QRWPRYH 2SHUDWLRQ LQWHUUXSWHG
%URNHQ&KLVHOV &KLSVFORJJHGLQ &KLVHO TRUQRUURXJK PRUWLVHV
TROUBLE SHOOTING
&DXVH 1RWSOXJJHGLQ )XVHRUFLUFXLWEORZQ 6RFNHWGRHVQRWIXQFWLRQ
'DPDJHGFRUGRUSOXJ 6ZLWFK...
User Manual - Page 9
... Washer
11 Bracket B
12 Knob 12A Handle 13 Spring
15 Gear Column
16 Guide Column
17 Knob
18 Depth Set Guide
19 Set Screw
20 Gear Shaft
21 Gear
22 Gear Access Plate
23 Gear Casing
24 Handle
25 Guide Sleeve
PARTS LIST
26 Stop Plate
27 Washer
28 Bolt
29 Motor 29-01 Capacitor 29...
User Manual - Page 11
... and an explanation of the complaint must bear the cost of this warranty, the product or part must be returned to the original purchaser that this product is no event be liable for death..., special or consequential damages arising from state to lack of our product. We will either repair or replace the product at our expense, but if we cannot readily and quickly provide you may also...
Harbor Freight Tools 35570 Reviews
Do you have an experience with the Harbor Freight Tools 35570 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Harbor Freight Tools yet.
Earn 750 points for your review!