Haier HB4800VA1M25 Support and Manuals
Get Help and Manuals for this Haier item
This item is in your list!
View All Support Options Below
Free Haier HB4800VA1M25 manuals!
Problems with Haier HB4800VA1M25?
Ask a Question
Free Haier HB4800VA1M25 manuals!
Problems with Haier HB4800VA1M25?
Ask a Question
Popular Haier HB4800VA1M25 Manual Pages
User Manual - Page 1
... KITS OR ACCESSORIES SHOULD BE USED WHEN INSTALLING OR MODIFYING THIS APPLIANCE, UNLESS OTHERWISE NOTED IN THESE INSTRUCTIONS.
FOLLOW ALL LOCAL CODES. No. 0010575351 E Installation & Operation Manual Air Handler
10 to 12 SEER 3 to 5 Tons
Models: HB3600VC1M25 HB4200VA1M25 HB4800VA1M25 HB6000VA1M25 HB6000VC1M25
WARNING WHEN THIS APPLIANCE IS INSTALLED IN AN ENCLOSED AREA, SUCH AS A GARAGE...
User Manual - Page 2
... fines. INDEX
TOPIC
General Physical dimensions Replacement Parts Source Installation Requirements Air Flow Orientation Horizontal Left-Hand Instructions Downflow Instructions Refrigerant Tubing Condensate Removal Electrical Connections Thermostat Wiring Orifice Change Circulating Air Duct Blower Performance Start-up Regular Maintenance Model Number Explanation
PAGE
1 2 3 3 4 5 6 7 7 8 9 11 11 12...
User Manual - Page 4
... structure. This unit can be suitably guarded against such damage by similar means. REPLACEMENT PARTS SOURCE Replacement parts are available through local distributors.When ordering replacement parts, give the COMPLETE model and serial numbers shown on a base, the base must be protected by installing behind protective barriers, being elevated or located out of the normal path of...
User Manual - Page 5
...conn. front
Downflow discharge (with plastic vertical pan only) (see page 6)
Important: Remove the horizontal pan when unit is installed in unconditioned i.e. (Garage, Attic ) application, or downflow applications, and install insulation kit on vertical ( donut shape ) drain pan.
*Upflow Discharge *Air Handler is factory ready for Upflow & Horizontal Right Discharge Application as shown.
5
User Manual - Page 6
...Replace...setting...driver for proper drainage by the installer... and placed under the entire unit with a separate drain line properly sloped and terminated in an area visible to over torque screws. WARNING: If incorrect knockouts are removed, flooding will cancel product warranty. of burrs and debris. Fig.2
6
Air...air pressure. HORIZONTAL LEFT-HAND INSTRUCTIONS
Important: Read instructions...
User Manual - Page 7
... which is recommended at the point where the duct meets with the return part of the Air Handler unit to allow easier removal of coils that are too tall. 7.
A 4" to 3" removable panel is accessible from the outside of air pressure
Before setting up position as shown in Fig.3. Fig.3
3" FLAT INSULATION RETAINER (both sides...
User Manual - Page 8
...exceed the total negative pressure, in inches, must be supported or routed to the plastic drain pan. The unit ...prevent damage to avoid strain or vibration. The condensate trap must be installed as measured in the return duct.
Use of plastics. A joint ... AND CHECK FOR LEAKS.
8
A trap must be used to the air handler. A "P " trap is coated with the seams sealed. They...
User Manual - Page 9
...of local code, the National Electrical Code. Model No. When an optional heat kit is recommended for "HB" air handlers installed without a heat kit.
9
Copper wire is installed refer to the electrical requirements in absence of the unit.
Blower
Ampacity Over-current Motor
208/230 208/230 FLA
HB4200VA1M25 -------- 15/15
2.2
Blower Motor H.P.
1/2
HB4800VA1M25 -------- 15/15...
User Manual - Page 10
...WAY VALUE
TO INDOOR
For detailed Thermostat, please connect FAN RELAY
CONTROL
corresponding terminal according to above
control specification. This mode is
RUN SWITCH
MODE SWITCH
Open for heating Close for cooling
control the indoor unit ...or select switch. THERMOSTAT WIRING
For Thermostat Control Environment-temperature and Air Conditioning open /stop , the wiring
diagram as shown diagram ...
User Manual - Page 11
...mechanical type or programmable type. For Thermostat Control Environment-temperature and Air Conditioning open /stop , the wiring
diagram as shown diagram 4. R : AC24V
TERMOSTAT
Y : COMPRESSOR
G
Y
R
C
G : FAN
For detailed Thermostat, please connect corresponding terminal according to above control specification. The detailed infor see the following diagram 6. Thermostat can adopt multi...
User Manual - Page 12
... connectors must be designed and installed as per local and/or national code.Refer to the exterior.
6)...replaced before any tubing connections are made. The supply plenum should be the dimensions specified by the factory. 12
Supply air ducts must be insulated and return ducts must be necessary to install a vapor barrier to the exterior of the outdoor unit. FOLLOW THESE INSTRUCTIONS...
User Manual - Page 13
...Measure the return air temperature. 4) Measure the supply temperature. This can allow for wet coil. Static Pressure
Model
HB4200VA1M25
HB4800VA1M25
CFM
High ...Model
CFM
HB3600VC1M25
HB6000VC1M25
0.15 0.2 0.25 0.3 0.35 0.4 0.5 1276 1244 1213 1184 1157 1127 1097
2063 2008 1953 1898 1841 1784
The air delivery can be checked by the following method; (The optional Heat Kit must be installed...
User Manual - Page 14
... maintained on a regular basis by the user is cleaned or replaced. Drain pans and drain tubing were leak checked with water. A certified service technician should be installed. Tubing should perform other physical damage. It is recommended that the circulating air filter(s) is to insure that a return air filter grille be leak free. Unit is connected.
Haier HB4800VA1M25 Reviews
Do you have an experience with the Haier HB4800VA1M25 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Haier yet.
Earn 750 points for your review!