GE JASRM24945 Support and Manuals
Get Help and Manuals for this General Electric item
This item is in your list!
View All Support Options Below
Free GE JASRM24945 manuals!
Problems with GE JASRM24945?
Ask a Question
Free GE JASRM24945 manuals!
Problems with GE JASRM24945?
Ask a Question
Popular GE JASRM24945 Manual Pages
Instruction Manual - Page 1
RM24945 Set
Universal Remote Instruction Manual
R24945 Remote
K24945 Locator Keyfob
Instruction Manual - Page 2
... navigate through the library of codes for your equipment.
2
Setup
Battery Installation for its own Volume/Mute .... 15 FIND IT Operation 16 Troubleshooting 21
Congratulations on using the code tables (on page 10 for your remote without batteries in these instructions may not be lost.
You can either set up the remote using the code search feature to learn how...
Instruction Manual - Page 3
... CODE SEARCH For setup.
0-9 Enter numbers for the PREV.CH button to the selected channel. PIP and SWAP operate your product.
With some DBS models ...remote might need to press the REC button once, then press it again for three seconds.
5 PREV.CH may be called EXIT. GUIDE displays satellite or cable on your DVD player when in -Picture features. Red Indicator Lights when any button is set...
Instruction Manual - Page 4
...toggle between the surround and main speakers when the receiver is enabled, pressing this presents a problem, it may be resolved by disabling the TV speakers by pressing the TEST button. If .... Operating Audio Functions
Note: Not all brands.
Sets the level of the TV button turns the receiver on the Receiver or Mini-System Point the remote control at the same time. Turning on .
1. ...
Instruction Manual - Page 5
...SURR MODE button until the red indicator stays on, then release the CODE SEARCH button.
2. Type
Type stored Code
TV
TV
VCR
SAT
CBL
AUDIO
DVD
8
9 Press FRONT, CENTER, or REAR... the desired device button (TV, VCR, etc.).
Press DELAY+ or DELAY- Note: after a valid code entry, the red indicator turns off , no further programming is achieved.
5. Note: If some buttons do...
Instruction Manual - Page 6
... turn on the device (TV, VCR, etc.) to be a code that causes the indicator light to find the second digit, repeat step 4.
6. Using Your Remote
Code Identification
The Code Identification Feature allows you to store a VCR code under your TV device button, follow the steps above for Code Search. To find the third digit. The red indicator...
Instruction Manual - Page 7
..., RCA and ProScan models require you to set up two different Mode buttons to control both parts of 1 to press the device button for the time required. Using Your Remote, cont. This feature...Through
This remote allows the 6 VCR transport buttons (i.e. a TV Combo, SAT/PVR, etc.
12
13
Sleep Function
The Sleep button enables the remote to control the TV part AND a separate code (under...
Instruction Manual - Page 8
... MUTE button and the red indicator turns off . Using Your Remote, cont. The remote is initially set all device Modes to that Mode.
1. If the programmed code has no Volume/Mute functions of its own then the Volume/Mute buttons will now punch-through control to the TV Mode device without the needing to change...
Instruction Manual - Page 9
...
A Keyfob or a Remote cannot find each other. FIND
For setup and for the Remote
NOTE: The remote is automatically set " and need to change the setting:
a. The Keyfob and the Remote are the simple steps. ...find your Remote to lose its settings, you wish to assign to .
The LED blinks and the Remote beeps the number of the Remote. The Remote is set to the same code as ...
Instruction Manual - Page 10
... beep. Important, if you used the default code of times corresponding to set them up. You can be set up . The LED blinks continuously to indicate that the Keyfob is in range, the FIND IT Locator Keyfob on your FIND IT Remote, the Remote warbles and the LED lights up . • Close the battery compartment. Using...
Instruction Manual - Page 11
... around while trying to operate all .
Checking Your Setup
To verify the ITEM # of your FIND IT Keyfobs corresponding to (1 thru 6). For example, if the Remote you want to control.
• Program the remote with a new code. • Install new batteries. (You might have to
reprogram your remote after you 're looking for it may not be...
Instruction Manual - Page 12
...
electrical circuit from the radio/TV experiencing the interference. • If necessary, consult your codes or programming instructions, you . Operation is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that is in a residential installation.
90 Day Limited Warranty
Jasco Products Company warrants...
GE JASRM24945 Reviews
Do you have an experience with the GE JASRM24945 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for GE yet.
Earn 750 points for your review!