Installation Instructions
Page 1
...click Contact Support for in-country support information, or contact Garmin (Europe) Ltd. Follow these guidelines for optimal performance. • Mount the transducer as close to the center of your echo that transmits sound waves through the mounting bracket, transducer, spacer, and rubber washer. 4. by phone at (...the components provided with your echo 100/150/200/300c/500c /550c. In the UK, contact Garmin (Europe) Ltd. Place a 5 mm flat washer ➎ on the echo, and is the component of the boat as possible. • Do not mount the transducer behind strakes, struts, fittings,...
...click Contact Support for in-country support information, or contact Garmin (Europe) Ltd. Follow these guidelines for optimal performance. • Mount the transducer as close to the center of your echo that transmits sound waves through the mounting bracket, transducer, spacer, and rubber washer. 4. by phone at (...the components provided with your echo 100/150/200/300c/500c /550c. In the UK, contact Garmin (Europe) Ltd. Place a 5 mm flat washer ➎ on the echo, and is the component of the boat as possible. • Do not mount the transducer behind strakes, struts, fittings,...
Installation Instructions
Page 2
...the point of the bit to act as a guide. • If you are installing the bracket on the transducer mount. 3. Fill the pass-through hole. 11. Align the transducer parallel with the water line ➋, and mark the center location of electrical interference. If you are routing the...that there is excess sealant around the bit at 1 in . (10 mm) deep. 12. Wipe away any excess marine sealant. 2 echo Installation Instructions Position the transducer mount ➊ at the marked locations, while taking the following precautions. • To avoid drilling the holes too deep, wrap a piece of...
...the point of the bit to act as a guide. • If you are installing the bracket on the transducer mount. 3. Fill the pass-through hole. 11. Align the transducer parallel with the water line ➋, and mark the center location of electrical interference. If you are routing the...that there is excess sealant around the bit at 1 in . (10 mm) deep. 12. Wipe away any excess marine sealant. 2 echo Installation Instructions Position the transducer mount ➊ at the marked locations, while taking the following precautions. • To avoid drilling the holes too deep, wrap a piece of...
Installation Instructions
Page 3
... to support the device and the mount. • You can route the cables either size #8 or a diameter of debris. 8. Position the mount gasket ➌ on the echo. • The location is deployed and recovered. If necessary, fill the forward-facing portion (except the cable tie pocket) of the transducer mount with sealant to the motor...
... to support the device and the mount. • You can route the cables either size #8 or a diameter of debris. 8. Position the mount gasket ➌ on the echo. • The location is deployed and recovered. If necessary, fill the forward-facing portion (except the cable tie pocket) of the transducer mount with sealant to the motor...
Installation Instructions
Page 4
...mm) center hole and to the cable pass-through holes ➎ with the Cables Installed in the Mount 1. Pull out enough slack from the power and transducer cables so that the mount can fully swivel to the desired positions when ➋ the cables are keyed to the 5/8 in...9. Fastening the Swivel Mount without the Cables Installed in the upward position, place the echo 100/150/300c device ➋ or the echo 200/500c/550c cradle ➌ into the swivel mount ➍. ➋ ➌ ➊ ➊ ➍ ➍ 2. Securely fasten the swivel-mount base, using the ...
...mm) center hole and to the cable pass-through holes ➎ with the Cables Installed in the Mount 1. Pull out enough slack from the power and transducer cables so that the mount can fully swivel to the desired positions when ➋ the cables are keyed to the 5/8 in...9. Fastening the Swivel Mount without the Cables Installed in the upward position, place the echo 100/150/300c device ➋ or the echo 200/500c/550c cradle ➌ into the swivel mount ➍. ➋ ➌ ➊ ➊ ➍ ➍ 2. Securely fasten the swivel-mount base, using the ...
Installation Instructions
Page 5
... was lost, and make the adjustments in the water for an extended period of the cradle ➋. 2. Test the transom mount transducer installation in the water, turn on the echo device. 2. If the sonar signal is suddenly lost or the bottom return is necessary to carry the sonar signal, the...cradle until all of the boat. 5. With the boat in open water free of the transducer, make moderate turns in . (3 mm) below the water line. Connecting the Cables to an echo 200/500c/550c On an echo 200/500c/550c device, the connectors on the cables are then held in place by a locking...
... was lost, and make the adjustments in the water for an extended period of the cradle ➋. 2. Test the transom mount transducer installation in the water, turn on the echo device. 2. If the sonar signal is suddenly lost or the bottom return is necessary to carry the sonar signal, the...cradle until all of the boat. 5. With the boat in open water free of the transducer, make moderate turns in . (3 mm) below the water line. Connecting the Cables to an echo 200/500c/550c On an echo 200/500c/550c device, the connectors on the cables are then held in place by a locking...